Linde 1167-04 – ML15 Production site Xiamen Operating Instructions SN CT1167X60001 and up

Description

• Model List:
  • ML15

• 1. Electric Pallet StackerML15
• 1.1. Table of content
• 1.2. Introduction
• 1.2.1. Introduction
• 1.2.2. General information
• 1.2.3. Conformity marking
• 1.2.4. Declaration that reflects the content of the declaration of conformity
• 1.2.5. Nameplate (LX)
• 1.2.6. Factory dataplate (for exports)
• 1.2.7. Intended use of the trucks
• 1.2.8. Additional information
• 1.2.9. Hazard assessment
• 1.2.10. Disposing of components and batteries
• 1.2.11. Impermissible use
• 1.2.12. Description of use and climatic conditions
• 1.2.13. Symbols used
• 1.2.14. Technical description
• 1.2.15. Series
• 1.3. Safety
• 1.3.1. Safety guidelines
• 1.3.2. Residual risks
• 1.3.3. Stability
• 1.3.4. Operating company
• 1.3.5. Drivers
• 1.3.6. Competent person
• 1.3.7. Regulations
• 1.3.8. Handling consumables
• 1.3.9. Use of lubricants
• 1.3.10. EMC Electromagnetic compatibility
• 1.4. Views
• 1.4.1. Drive directions
• 1.4.2. Overview of main components
• 1.4.3. Dataplate and safety labels
• 1.4.4. Load label
• 1.5. Operation
• 1.5.1. Intended use of the trucks
• 1.5.2. First use
• 1.5.3. Daily checks before use
• 1.5.4. Checking the working environment
• 1.5.5. General information on batteries
• 1.5.6. Charging and discharging batteries
• 1.5.7. Drive operations
• 1.5.7.1. Description
• 1.5.7.2. Starting
• 1.5.7.3. Forward travel.reverse travel
• 1.5.7.4. Braking
• 1.5.7.5. Safety reverser
• 1.5.7.6. Creep Speed function
• 1.5.7.7. Steering
• 1.5.7.8. Using the truck on a slope
• 1.5.8. Hydraulic operations
• 1.5.8.1. Use of the mast
• 1.5.8.2. Working with loads
• 1.5.8.3. Emergency lowering
• 1.5.9. Before leaving the equipment
• 1.5.10. Putting the equipment back into operation
• 1.5.11. Slinging
• 1.5.12. Transporting the truck
• 1.6. Maintenance
• 1.6.1. General maintenance information
• 1.6.1.1. General
• 1.6.1.2. Daily inspection
• 1.6.1.3. Servicing and maintenance personnel training and qualification
• 1.6.1.4. Battery maintenance staff
• 1.6.1.5. Maintenance operations that do not require special training
• 1.6.1.6. Technical inspection and maintenance data
• 1.6.2. Service plan
• 1.6.3. Maintenance work
• 1.6.3.1. Changing the battery
• 1.6.3.2. Lubrication point
• 1.6.3.3. Check the hydraulic oil level
• 1.6.3.4. Topping up the gear oil
• 1.6.3.5. Checking the fuses
• 1.6.4. Tyre operation
• 1.6.4.1. Drive Wheel
• 1.6.4.2. Load wheels removing and installing
• 1.6.4.3. Caster Removal and Installation
• 1.6.5. Malfunction analysis
• 1.7. Technical data
• 1.7.1. ML15 technical parameters
• 1.8. Schematic diagrams
• 1.8.1. Electrical diagrams
• 1.8.2. Hydraulics diagrams
• 1.8.3. Brake Principle
• 1.8.4. Diagram of major stressed structural parts