Linde 351-04 – H25D, H25T, H30D, H30T Production site Xiamen Workshop Manuals SN 04.07 and up SN up to 01.11

Description

• Model List:
  • H25D
  • H25T
  • H30D
  • H30T

• 1. Regular testing
• 1.1. Table of content
• 1.2. Regular testing
• 1.3. Electric motor
• 1.4. Internal combustion engine
• 1.5. Drive axle
• 1.6. Chassis
• 1.7. Drivers compartment
• 1.8. Steering systems
• 1.9. Wheels and tyres
• 1.10. Brake system
• 1.11. Operating devices
• 1.12. Electrics.electronics
• 1.13. Hydraulics
• 1.14. Lift mast
• 1.15. Load support
• 1.16. Attachments
• 1.17. Special equipment.accessories
• 2. Service case Release tools for contacts
• 2.1. Table of content
• 2.2. Safety information
• 2.3. Information
• 2.4. Overview
• 2.5. Plug systems
• 3. Steering axle crimping tool
• 3.1. Table of content
• 3.2. Crimping tool
• 3.3. Replacement kits
• 3.4. Steering axle 301.302.303
• 3.5. Steering axle 1601
• 3.6. Steering axle 1602.1603
• 4. Deutz engine
• 4.1. Frontpage
• 4.2. Table of contents
• 4.3. Checking the compression pressure
• 4.4. Mounting engine on assembly block and demounting
• 4.5. Setting valve clearance
• 4.6. Removing and installing the rocker arm and rocker arm bracket
• 4.7. Disassembling, assembling and checking the rocker arm and rocker arm bracket
• 4.8. Removing and installing cylinder head
• 4.9. Checking piston overhang
• 4.10. Removing and installing the crankcase bleeding
• 4.11. Removing and installing the exhaust line
• 4.12. Removing and install the charge air line
• 4.13. Removing and installing the turbocharger
• 4.14. Removing and installing the intake manifold
• 4.15. Removing and installing the exhaust gas return valve
• 4.16. Removing and installing the exhaust gas return pipe
• 4.17. Removing and installing the exhaust gas collection pipe (Exhaust gas recirculation)
• 4.18. Removing and installing the lifting magnet (Start amount release)
• 4.19. Renewing the injection lines
• 4.20. Removing and installing the fuel injectors
• 4.21. Removing and installing the lifting magnet (charge air pressuredependent full load stop)
• 4.22. Installing and removing charge air pressuredependent full load stop
• 4.23. Removing and installing fuel pipes
• 4.24. Removing and installing the fuel filter console
• 4.25. Removing and installing the fuel supply pump
• 4.26. Removing and installing the lubricating oil cooler
• 4.27. Removing and installing the oil filter console
• 4.28. Removing and installing the oil pressure switch
• 4.29. Removing and installing the thermostat (Lubricating oil cooler)
• 4.30. Removing and installing the control line
• 4.31. Removing and installing the coolant pump
• 4.32. Checking the thermostat (in the removed state)
• 4.33. Removing and installing the thermostat
• 4.34. Removing and installing the thermostat housing
• 4.35. Removing and installing temperature transmitter
• 4.36. Removing and installing the lifting magnet (Engine shutdown)
• 4.37. Removing and installing the Vbelt pulley
• 4.38. Renew Vbelts, check Vbelt tension
• 4.39. Removing and installing the flywheel
• 4.40. Removing and installing the hydraulic pump
• 4.41. Removing and installing the generator
• 4.42. Removing and installing the starter
• 4.43. Removing and installing the heating plugs
• 4.44. Removing and installing the glow plug
• 4.45. Standard tools
• 4.46. Special tools
• 5. connectdesk
• 5.1. Table of content
• 5.2. Introduction
• 5.3. System overview
• 5.4. Hardware
• 5.5. Software
• 5.6. Status checking (PreOpCheck)
• 6. connectportal
• 6.1. Table of content
• 6.2. Introduction
• 6.3. Data transfer
• 6.4. Hardware
• 6.5. Software
• 7. connectdt operating hoursRetrofitting the connectdt operating hours
• 7.1. Table of content
• 7.2. connectdt operating hours
• 8. connectdt trouble codesRetrofitting connectdt trouble codes
• 8.1. Table of content
• 8.2. connectdt trouble codes