Komatsu 330M Dump Truck Operation and Maintenance Manual DG745

Komatsu 330M Dump Truck Operation and Maintenance Manual DG745 - Image 2

Komatsu 330M Dump Truck Operation and Maintenance Manual DG745 - Image 3

Komatsu 330M Dump Truck Operation and Maintenance Manual DG745 - Image 4

Komatsu 330M Dump Truck Operation and Maintenance Manual DG745 - Image 5

komatsu 330m dump truck operation and maintenance manual dg745 2 2

komatsu 330m dump truck operation and maintenance manual dg745 3 2

Komatsu 330M Dump Truck Operation and Maintenance Manual DG745

$30.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: DG745
Format: PDF
Size: 1.9MB
Number of Pages: 142

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- 330M Dump Truck

1. MAIN MENU
2. COVER
3. INTRODUCTION
3.1. FOREWORD
3.2. ALERTS Page DANGER, WARNING, CAUTION
3.3. TABLE OF CONTENTS
3.4. TRUCK MODEL ILLUSTRATION
3.5. About This Manual
3.6. STANDARD TABLES
4. SAFETY
4.1. GENERAL SAFETY
4.2. PRECAUTIONS DURING OPERATION
4.2.1. OPERATING THE MACHINE
4.2.2. TOWING
4.2.3. BATTERY
4.3. PRECAUTIONS FOR MAINTENANCE
4.3.1. BEFORE CARRYING OUT MAINTENANCE
4.3.2. DURING MAINTENANCE
4.3.3. TIRES
4.4. WARNINGS AND CAUTIONS, and Instruction Plates / Decals
5. OPERATION
5.1. OPERATING INSTRUCTIONS
5.1.1. PREPARING FOR OPERATION
5.1.2. SAFETY IS THINKING AHEAD
5.1.3. At The Truck Ground Level Walk AroundInspection
5.2. ENGINE STARTUP SAFETY PRACTICES
5.3. AFTER ENGINE HAS STARTED
5.4. MACHINE OPERATION SAFETY PRECAUTIONS
5.5. LOADING
5.6. HAULING
5.7. PASSING
5.8. DUMPING
5.9. SAFE PARKING PROCEDURES
5.10. SHUTDOWN PROCEDURE
5.11. TOWING
5.12. BRAKE RELEASE
5.13. RELEASE OF PARKING BRAKE
5.14. RELEASE OF EMERGENCY BRAKE
5.15. OPERATOR CAB AND CONTROLS
5.15.1. Steering Wheel And Controls
5.15.2. Retarder Control Lever
5.15.3. Service Brake Pedal
5.15.4. Throttle Pedal
5.15.5. Center Console and Controls
5.15.6. ENGINE ELECTRONIC CONTROL SYSTEM
5.15.6.1. DETERMINING FAULT CODES
5.15.6.2. EXITING THE DIAGNOSTICS MODE
5.15.7. Differential Lock Pedal
5.15.8. Hoist Control Valve
5.15.8.1. SAFETY LOCK
5.15.9. OPERATOR SEAT
5.16. INSTRUMENT PANEL AND INDICATORS
5.17. GAUGE AND MONITOR PANEL
5.18. INDICATORS AND CONTROL PANEL
5.19. INDICATORS AND CONTROL PANEL
5.20. INSTRUMENT PANEL RIGHT SIDE
6. MAINTENANCE
6.1. LUBRICATION AND SERVICE
6.1.1. Lubrication Chart
6.1.2. HOUR (SHIFT) Lubrication and Maintenance Checks
6.1.3. HOUR Lubrication and Maintenance Checks
6.1.4. HOUR Lubrication and Maintenance Checks
6.1.5. HOUR Lubrication and Maintenance Checks
6.1.6. HOUR Lubrication and Maintenance Checks
6.1.7. HOUR Lubrication and Maintenance Checks
6.2. HYDRAULIC TANK SERVICE
6.3. HIGH PRESSURE HYDRAULIC FILTERS
6.4. TRANSMISSION FILTER SERVICE
6.5. PERIODIC REPLACEMENT OF COMPONENT PARTS FOR SAFETY DEVICES
6.6. BRAKE CIRCUIT CHECKOUT AND ADJUSTMENT
6.6.1. CHECKING FRONT BRAKE PAD WEAR
6.6.2. TESTING BRAKE PRESSURE
6.6.3. CHECKING REAR BRAKE DISC WEAR
6.6.4. BRAKE SYSTEM BLEEDING
6.6.5. PARKING BRAKE INSPECTION ADJUSTMENT
7. SPECIFICATIONS
7.1. MAJOR COMPONENTS AND SPECIFICATIONS
7.2. SPECIFICATIONS
8. OPTIONAL EQUIPMENT
9. PAYLOAD METER II INDEX
10. PAYLOAD METER II
10.1. PAYLOAD METER II ON BOARD WEIGHING SYSTEM (OBWS)
10.2. GENERAL INFORMATION
10.2.1. Haul Cycles
10.3. LIGHTS, SWITCHES, and COMPONENTS
10.4. TIPS FOR OPERATION
10.5. EXTERNAL DISPLAY LIGHTS
10.6. THEORY OF OPERATION
10.6.1. Basic Description
10.6.2. Inclinometer
10.6.3. Linkage Factor
10.6.4. Gain Factor
10.6.5. Brake Lock
10.6.6. Sources of Error
10.6.7. Typical Data From Service Check Mode
10.6.8. Example Calculation of Payload
10.6.9. Viewing Payload Calculation Inputs
10.6.10. Checking the Gain
10.6.11. Adjusting the Gain
10.7. TYPES OF DATA STORED
10.7.1. Cycle Data
10.7.2. Engine ON/OFF Data
10.7.3. Fault Codes and Warning Data
10.7.4. Engine Operation
10.7.5. Total Payload and Total Number of Cycles
10.7.6. Other Data
10.8. OPERATOR FUNCTIONS
10.8.1. Using the Operator Load Counter
10.8.2. Viewing the Operator Load Counter
10.8.3. Clearing the Operator Load Counter
10.8.4. Dimming the Lights on the Display
10.9. INITIAL SETUP OF PAYLOAD METER
10.9.1. Switch Settings
10.9.2. Checking the Operator Check Mode
10.9.3. Checking the Service Check Mode
10.9.4. Checking the Gt setting
10.9.5. Checking the Inclinometer Settings
10.9.6. Calibrating a Truck
10.10. DISPLAYS AT STARTUP
10.11. NORMAL OPERATION
10.12. SETUP AND MAINTENANCE
10.12.1. Setting The Speed Limit
10.12.2. Setting the Option Code
10.12.3. Setting The Machine I.D. Code
10.12.4. Setting The Operator I.D. Code
10.12.5. Setting The Time and Date
10.13. DOWNLOAD OF INFORMATION
10.14. DISPLAY OF FAULT CODES
10.15. Monitoring Input Signals
10.16. Service Check Mode
10.17. UP Factor Payload Calculation Gain
10.18. PL Mode Load Calculation Timing
10.19. FINAL GEAR RATIO SELECTION
10.20. BATTERY REPLACEMENT PROCEDURE
10.20.1. Replacing the Battery
10.20.2. After Replacing the Battery
10.21. SUSPENSION PRESSURE SENSOR
10.22. PAYLOAD METER BACK PANEL
10.23. CONNECTIONS
10.24. PAYLOAD METER 2 REINITIALIZATION PROCEDURE
10.25. PAYLOAD CIRCUIT NUMBERS

Rate this product