Komatsu PC150-6K, PC150LC-6K Hydraulic Excavator Operation and Maintenance Manual UEAM000403

Description

• Model List:
  • PC150-6K Hydraulic Excavator
  • PC150LC-6K Hydraulic Excavator

• 1. MAIN MENU
• 2. COVER
• 3. FOREWORD
• 4. SAFETY INFORMATION
• 4.1. SAFETY MESSAGES
• 4.2. VIBRATION
• 5. INTRODUCTION
• 5.1. INTENDED USE
• 5.2. FEATURES
• 5.3. BREAKING IN YOUR NEW MACHINE
• 6. LOCATION OF PLATES, TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
• 6.1. MACHINE SERIAL NO. PLATE POSITION
• 6.2. ENGINE SERIAL NO. PLATE POSTION
• 6.3. TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
• 6.4. MACHINE SERIAL PLATE
• 7. CONTENTS
• 8. SAFETY
• 8.1. GENERAL PRECAUTIONS
• 8.2. PRECAUTIONS DURING OPERATION
• 8.2.1. BEFORE STARTING ENGINE
• 8.2.2. OPERATING MACHINE
• 8.2.3. TRANSPORTATION
• 8.2.4. BATTERY
• 8.2.5. TOWING
• 8.2.6. BUCKET WITH HOOK
• 8.3. PRECUATIONS FOR MAINTENANCE
• 8.3.1. BEFORE CARRYING OUT MAINTENANCE
• 8.3.2. DURING MAINTENANCE
• 8.4. POSITION FOR ATTACHING SAFETY LABELS
• 8.4.1. POSITION FOR ATTACHING SAFETY LABELS
• 8.5. MEMO
• 9. OPERATION
• 9.1. GENERAL VIEW
• 9.1.1. GENERAL VIEW OF MACHINE
• 9.1.2. GENERAL VIEW OF CONTROLS AND GAUGES
• 9.2. EXPLANATION OF COMPONENTS
• 9.2.1. MACHINE MONITOR
• 9.2.2. METERS
• 9.2.3. SWITCHES
• 9.2.4. CONTROL LEVERS, PEDALS
• 9.2.5. HEATER
• 9.2.6. AIR CONDITIONER (OPTION)
• 9.2.7. CAB RADIO (OPTION)
• 9.2.8. FUSE
• 9.2.9. FUSIBLE LINK
• 9.2.10. CONTROLLERS
• 9.2.11. TOOL BOX
• 9.2.12. REFUELLING PUMP
• 9.2.13. HANDLING THE ACCUMULATOR
• 9.3. OPERATION
• 9.3.1. CHECK BEFORE STARTING ENGINE
• 9.3.2. STARTING ENGINE
• 9.3.3. OPERATIONS AND CHECKS AFTER STARTING ENGINE
• 9.3.4. MOVING MACHINE OFF
• 9.3.5. STEERING MACHINE
• 9.3.6. STOPPING MACHINE
• 9.3.7. SWINGING
• 9.3.8. OPERATION OF WORK EQUIPMENT
• 9.3.9. HANDLING ACTIVE MODE
• 9.3.10. WORKING MODE SELECTORN
• 9.3.11. PROHIBITIONS FOR OPERATION
• 9.3.12. PRECAUTIONS FOR OPERATION
• 9.3.13. PRECAUTIONS WHEN TRAVELLING UP OR DOWN HILLS
• 9.3.14. HOW TO ESCAPE FROM MUD
• 9.3.15. WORK POSSIBLE USING HYDRAULIC EXCAVATOR
• 9.3.16. REPLACEMENT AND INVERSION OF BUCKET
• 9.3.17. PARKING THE MACHINE
• 9.3.18. CHECK AFTER FINISHING WORK
• 9.3.19. STOPPING ENGINE
• 9.3.20. CHECK AFTER STOPPING ENGINE
• 9.4. TRANSPORTATION
• 9.4.1. LOADING, UNLOADING WORK
• 9.5. COLD WEATHER OPERATION
• 9.5.1. PRECAUTIONS FOR LOW TEMPERATURE
• 9.5.2. PRECAUTIONS AFTER COMPLETION WORK
• 9.6. LONGTERM STORAGE
• 9.6.1. BEFORE STORAGE
• 9.6.2. DURING STORAGE
• 9.6.3. AFTER STORAGE
• 9.6.4. STARTING MACHINE AFTER LONGTERM STORAGE
• 9.7. TROUBLESHOOTING
• 9.7.1. PHENOMENA THAT ARE NOT FAILURES
• 9.7.2. METHOD OF TOWING MACHINE
• 9.7.3. USING METHOD FOR LIGHTWEIGHT TOWING HOLE
• 9.7.4. PRECAUTIONS ON PARTICULAR JOBSITES
• 9.7.5. IF BATTERY IS DISCHARGED
• 9.7.6. OTHER TROUBLE
• 10. MAINTENANCE
• 10.1. GUIDES TO MAINTENANCE
• 10.2. OUTLINES OF SERVICE
• 10.2.1. OUTLINE OF OIL, FUEL, COOLANT
• 10.2.2. EXPLANATION OF LUBRICATION CHART DECAL
• 10.2.3. OUTLINE OF ELECTRICAL SYSTEM
• 10.2.4. OUTLINE OF HYDRAULIC SYSTEM
• 10.3. WEAR PARTS LIST
• 10.4. USE OF FUEL, COOLANT AND LUBRICANTS ACCORDING
• 10.5. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
• 10.5.1. LIST OF NECESSARY TOOLS
• 10.5.2. TORQUE LIST
• 10.6. PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
• 10.7. MAINTENANCE SCHEDULE CHART
• 10.7.1. MAINTENANCE SCHEDULE CHART
• 10.7.2. MAINTENANCE WHEN USING HYDRAULIC BREAKER
• 10.8. SERVICE PROCEDURE
• 10.8.1. INITIAL 250 HOURS SERVICE
• 10.8.1.1. REPLACE FUEL FILTER CARTRIDGE
• 10.8.2. WHEN REQUIRED
• 10.8.2.1. CHECK, CLEAN AND REPLACE AIR CLEANER ELEMENT
• 10.8.2.2. CLEAN INSIDE OF COOLING SYSTEM
• 10.8.2.3. CHECK AND TIGHTEN TRACK SHOE BOLTS
• 10.8.2.4. CHECK AND ADJUST TRACK TENSION
• 10.8.2.5. CHECK ELECTRICAL INTAKE AIR HEATER
• 10.8.2.6. CHECK ALTERNATOR
• 10.8.2.7. CHECK START MOTOR
• 10.8.2.8. REPLACE BUCKET SIDE CUTTERS
• 10.8.2.9. REPLACE BUCKET TEETH
• 10.8.2.10. ADJUST BUCKET CLEARANCE
• 10.8.2.11. CHECK WINDOW WASHER FLUID LEVEL, ADD FLUID
• 10.8.2.12. CHECK, MAINTAIN AIR CONDITIONER
• 10.8.2.13. CLEAN INLINE FILTER
• 10.8.3. CHECK BEFORE STARTING
• 10.8.3.1. CHECK COOLANT LEVEL, ADD COOLANT
• 10.8.3.2. CHECK OIL LEVEL IN ENGINE OIL PAN, ADD OIL
• 10.8.3.3. CHECK FUEL LEVEL, ADD FUEL
• 10.8.3.4. CHECK OIL LEVEL IN HYDRAULIC TANK, ADD OIL
• 10.8.3.5. CHECK AIR CLEANER FOR CLOGGING
• 10.8.3.6. CHECK ELECTRIC WIRINGS
• 10.8.3.7. CHECK FUNCTION OF HORN
• 10.8.3.8. CHECK FOR WATER IN FUEL SEDIMENTOR
• 10.8.3.9. CHECK FOR WATER IN PRIMARY FUEL FILTER, DRAIN WATER
• 10.8.4. EVERY 100 HOURS SERVICE
• 10.8.4.1. LUBRICATING
• 10.8.4.1.1. BOOM CYLINDER FOOT PIN (2 POINTS)
• 10.8.4.1.2. BOOM FOOT PIN (2 POINTS)
• 10.8.4.1.3. BOOM CYLINDER ROD PIN (2 POINTS)
• 10.8.4.1.4. ARM CYLINDER FOOT PIN (1 POINT)
• 10.8.4.1.5. BOOMARM COUPLING PIN (1 POINT)
• 10.8.4.1.6. ARM CYLINDER ROD END (1 POINT)
• 10.8.4.1.7. BUCKET CYLINDER FOOT PIN (1 POINT)
• 10.8.4.1.8. ARMLINK COUPLING PIN (1 POINT)
• 10.8.4.1.9. ARMBUCKET COUPLING PIN (1 POINT)
• 10.8.4.1.10. LINK COUPLING PIN (2 POINTS)
• 10.8.4.1.11. BUCKET CYLINDER ROD ENG (1 POINT)
• 10.8.4.1.12. BUCKETLINK COUPLING PIN (1 POINT)
• 10.8.4.2. CHECK OIL LEVEL IN SWING MACHINERY CASE, ADD OIL
• 10.8.4.3. DRAIN WATER AND SEDIMENT FROM FUEL TANK
• 10.8.4.4. CLEAN FRESH AIR INTAKE FILTER
• 10.8.5. EVERY 250 HOURS SERVICE
• 10.8.5.1. CHECK OIL LEVEL IN FINAL DRIVE CASE, ADD OIL
• 10.8.5.2. CHECK LEVEL OF BATTERY ELECTROLYTE
• 10.8.5.3. LUBRICATE SWING CIRCLE (2 POINTS)
• 10.8.5.4. BELTS, GENERAL
• 10.8.5.5. CHECK ALTERNATOR, FAN AND WATER PUMP BLET TENSION, ADJUST CHECKING TENSION
• 10.8.5.6. CHECK AIR CONDITIONER COMPRESSOR BELT TENSION, ADJUST
• 10.8.6. EVERY 500 HOURS SERVICE
• 10.8.6.1. REPLACE FUEL FILTER CARTRIDGE
• 10.8.6.2. CHECK SWING PINION GREASE LEVEL, ADD GREASE
• 10.8.6.3. CHANGE OIL IN ENGINE OIL PAN, REPLACE ENGINE OIL FILTER CARTRIDGE
• 10.8.6.4. CLEAN AND INSPECT RADIATOR FINS, OIL COOLER FINS AND CONDENSER FINS (ONLY FOR MACHINES EQUIPPED WITH AIR CONDITIONER)
• 10.8.6.5. REPLACE HYDRAULIC FILTER ELEMENT
• 10.8.7. EVERY 1000 HOURS SERVICE
• 10.8.7.1. CHANGE OIL IN SWING MACHINERY CASE
• 10.8.7.2. CHECK ALL TIGHTENING PARTS OF TURBOCHARGER
• 10.8.7.3. CHECK PLAY OF TURBOCHARGER ROTOR
• 10.8.7.4. CHECK FAN BELT TENSIONER BEARING BELT AND FAN HUB
• 10.8.7.5. CHECK FAN BELT TENSION
• 10.8.8. EVERY 2000 HOURS SERVICE
• 10.8.8.1. CHANGE OIL IN FINAL DRIVE CASE
• 10.8.8.2. CLEAN HYDRAULIC TANK STRAINER
• 10.8.8.3. CLEAN, CHECK TURBOCHARGER
• 10.8.8.4. CHECK ALTERNATOR, STARTING MOTOR
• 10.8.8.5. CHECK ENGINE VALVE CLEARANCE, ADJUST
• 10.8.8.6. CHECK VIBRATION DAMPER
• 10.8.8.7. CHANGE ANTIFREEZE
• 10.8.9. EVERY 4000 HOURS SERVICE
• 10.8.9.1. CHECK WATER PUMP
• 10.8.10. EVERY 5000 HOURS SERVICE
• 10.8.10.1. CHANGE OIL IN HYDRAULIC TANK
• 10.9. MEMO
• 11. SPECIFICATIONS
• 11.1. SPECIFICATIONS
• 11.1.1. PC1506K, PC150LC6K
• 11.1.2. LIFTING CAPACITY CHART
• 12. OPTIONS, ATTACHMENTS
• 12.1. PRECAUTIONS RELATED TO SAFETY
• 12.1.1. PRECAUTIONS WHEN INSTALLING ATTACHMENTS
• 12.2. HANDLING BUCKET WITH HOOK
• 12.2.1. CHECKING FOR DAMAGE TO BUCKET WITH HOOK
• 12.2.2. PROHIBITED OPERATIONS
• 12.2.3. PRECAUTIONS DURING OPERATIONS
• 12.3. MACHINES READY FOR ATTACHMENTS
• 12.3.1. ATTACHMENT MOUNTING/DISMOUNTING PROCEDURE
• 12.4. INTRODUCTION OF ATTACHMENTS
• 12.4.1. SPECIFICATION, USE
• 12.4.2. ATTACHMENT INSTALLATION COMBINATION TABLE
• 12.4.3. SELECTION OF TRACK SHOES
• 12.4.4. SELECTION OF BUCKET TEETH
• 12.4.5. HANDLING TRAPEZOIDAL BUCKET
• 12.4.6. HANDLING THE CLAMSHELL BUCKET
• 12.5. EXTENDING MACHINE SERVICE LIFE
• 12.5.1. HYDRAULIC BREAKER
• 12.5.2. POWER RIPPER
• 12.5.3. MAIN FIELDS OF APPLICATIONS
• 12.5.4. FORK GRAB
• 12.5.5. GRAPPLE BUCKET
• 12.5.6. SCRAP GRAPPLE
• 12.5.7. CRUSHER SMASHER
• 12.5.8. HYDRAULIC PILE DRIVER
• 12.5.9. HYDRAULIC EXCAVATOR WITH MULTIPURPOSE CRANE
• 12.6. MEMO