Description
-
Model List:
- WA380-5H Wheel Loader
- 1. FOREWORD
- 1.1. FOREWORD
- 1.2. SAFETY INFORMATION
- 1.3. INTRODUCTION
- 1.3.1. INTENDED USE
- 1.3.2. DIRECTIONS OF MACHINE
- 1.4. NECESSARY INFORMATION
- 1.4.1. PIN/MACHINE SERIAL NO. PLATE AND POSITION
- 1.4.2. ENGINE SERIAL NO. PLATE AND POSITION
- 1.4.3. ROPS/FOPSCAB SERIAL NO. PLATE
- 1.4.4. AXLE SERIAL NO. PLATE
- 1.4.5. TRANSMISSION SERIAL NO. PLATE
- 1.4.6. SEAT OPERATOR SERIAL NO. PLATE
- 1.4.7. POSITION OF SERVICE METER
- 1.4.8. TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
- 1.5. CONTENTS
- 1.6. DIMENSIONS, WEIGHTS AND OPERATING DATA
- 1.6.1. WA3805H DIMENSIONS, WEIGHTS AND OPERATING DATA
- 1.7. CECONFORMING EQUIPMENT
- 1.7.1. CECONFORMING EQUIPMENT
- 1.7.2. MANUFACTURERSUPPLIED CECONFORMING EQUIPMENT, ACCORDING TO DOCUMENT 42193H1900
- 2. SAFETY
- 2.1. SAFETY LABELS
- 2.1.1. LOCATION OF SAFETY LABELS
- 2.1.2. SAFETY LABELS
- 2.2. GENERAL PRECAUTIONS
- 2.3. PRECAUTIONS FOR OPERATION
- 2.3.1. STARTING ENGINE
- 2.3.2. OPERATION
- 2.4. TRANSPORTATION
- 2.5. BATTERY
- 2.6. TOWING
- 2.7. PRECAUTIONS FOR MAINTENANCE
- 2.8. PRECAUTIONS WITH TIRES
- 3. OPERATION
- 3.1. GENERAL VIEW
- 3.1.1. GENERAL VIEW OF MACHINE
- 3.1.2. GENERAL VIEW OF CONTROLS AND GAUGES
- 3.2. EXPLANATION OF COMPONENTS
- 3.2.1. MACHINE MONITOR
- 3.2.2. SWITCHES
- 3.2.3. CONTROL LEVERS, PEDALS
- 3.2.4. STEERING TILT LOCK LEVER
- 3.2.5. CAP WITH LOCK
- 3.2.6. SAFETY BAR
- 3.2.7. TOWING PIN
- 3.2.8. GREASE PUMP
- 3.2.9. CAB DOOR OPEN LOCK
- 3.2.10. CAB WINDOW OPEN LOCK
- 3.2.11. BACKUP ALARM
- 3.2.12. FUSE
- 3.2.13. SLOWBLOW FUSE
- 3.2.14. TAKING OFF POWER
- 3.2.15. AIR CONDITIONER
- 3.2.16. CAB WIPER
- 3.2.17. DUST INDICATOR
- 3.3. OPERATION
- 3.3.1. CHECK BEFORE STARTING
- 3.3.2. ADJUSTMENT BEFORE STARTING
- 3.3.3. OPERATIONS BEFORE STARTING
- 3.3.4. STARTING ENGINE
- 3.3.5. CHECKS AFTER STARTING
- 3.3.6. STOPPING ENGINE
- 3.3.7. MOVING MACHINE OFF (DIRECTIONAL, SPEED), STOPPING
- 3.3.8. CHANGING GEAR SPEED
- 3.3.9. CHANGING DIRECTION
- 3.3.10. STOPPING MACHINE
- 3.3.11. TRANSMISSION CUTOFF
- 3.3.12. TURNING
- 3.3.13. OPERATION OF WORK EQUIPMENT
- 3.3.14. WORKING POSSIBILITY
- 3.3.15. PRECAUTIONS FOR OPERATION
- 3.3.16. ADJUSTING WORK EQUIPMENT
- 3.3.17. PARKING MACHINE
- 3.3.18. CHECKS AFTER WORK
- 3.3.19. LOCKING
- 3.3.20. HANDLING THE TIRES
- 3.4. TRANSPORTATION
- 3.4.1. TRANSPORTATION PROCEDURE
- 3.4.2. LIFTING MACHINE
- 3.5. COLD WEATHER OPERATION
- 3.5.1. LOW TEMPERATURE
- 3.5.2. AFTER COMPLETION OF WORK
- 3.5.3. AFTER COLD WEATHER
- 3.5.4. WARMINGUP OF STEERING HYDRAULIC
- 3.6. LONGTERM STORAGE
- 3.6.1. BEFORE STORAGE
- 3.6.2. DURING STORAGE
- 3.6.3. AFTER STORAGE
- 3.7. TROUBLESHOOTING
- 3.7.1. WHEN MACHINE RUNS OUT OF FUEL
- 3.7.2. TOWING THE MACHINE
- 3.7.3. BATTERY IS DISCHARGED
- 3.7.4. OTHER TROUBLE
- 4. MAINTENANCE
- 4.1. GUIDES TO MAINTENANCE
- 4.2. OUTLINES OF SERVICE
- 4.2.1. OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC
- 4.2.2. OUTLINE OF ELECTRIC SYSTEM
- 4.3. WEAR PARTS
- 4.3.1. WEAR PARTS LIST
- 4.4. LUBRICANTS AND OPERATING MEANS
- 4.4.1. LUBRICATION CHART
- 4.4.2. LUBRICANTS, FUELS AND FILLING CAPACITIES
- 4.5. STANDARD TIGHTENING TORQUES
- 4.6. PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
- 4.7. MAINTENANCE SCHEDULE CHART
- 4.7.1. MAINTENANCE SCHEDULE CHART
- 4.8. SERVICE PROCEDURE
- 4.8.1. INITIAL 50 HOURS SERVICE
- 4.8.2. INITIAL 250 HOURS SERVICE
- 4.8.3. INITIAL 1000 HOURS SERVICE
- 4.8.4. WHEN REQUIRED
- 4.8.5. CHECK BEFORE STARTING
- 4.8.6. EVERY 50 HOURS SERVICE
- 4.8.7. EVERY 100 HOURS SERVICE
- 4.8.8. EVERY 250 HOURS SERVICE
- 4.8.9. EVERY 500 HOURS SERVICE
- 4.8.10. EVERY 1000 HOURS SERVICE
- 4.8.11. EVERY 2000 HOURS SERVICE
- 4.8.12. EVERY 4000 HOURS SERVICE
- 4.8.13. EVERY 8000 HOURS SERVICE
- 5. TECHNICAL DATA
- 5.1. TECHNICAL DATA
- 5.2. NOISE EMISSION LEVELS
- 5.3. VIBRATION LEVELS
- 5.3.1. OPERATING CONDITION
- 5.3.2. GUIDE TO REDUCE VIBRATION LEVELS ON MACHINE
- 5.4. LIMIT VALUES FOR SLOPES
- 6. ATTACHMENTS, OPTIONS
- 6.1. HANDLING LOAD METER
- 6.1.1. GENERAL LOCATIONS
- 6.1.2. LOAD METER FUNCTIONS
- 6.1.3. HANDLING LOAD METER DISPLAY
- 6.1.4. METHOD OF SETTING TIME ON CLOCK
- 6.1.5. PRINTER OUTPUT
- 6.2. HANDLING TORQUE CONVERTER LOCKUP
- 6.2.1. GENERAL LOCATIONS
- 6.2.2. METHOD OF OPERATION
- 6.2.3. WARNING/LIMIT FUNCTIONS FOR TRAVEL SPEED
- 6.3. HANDLING AUTOMATIC AIRCONDITIONER
- 6.3.1. GENERAL LOCATIONS AND FUNCTIONS OF CONTROL PANEL
- 6.3.2. METHOD OF OPERATION
- 6.3.3. PRECAUTIONS WHEN USING
- 6.3.4. INSPECTION AND MAINTENANCE
- 6.4. CENTRAL LUBRICATION
- 6.4.1. OPERATION
- 6.4.2. DISPLAY AND CONTROL UNIT
- 6.4.3. CHANGING THE LUBRICATION INTERVAL TIMES
- 6.5. HANDLING MULTIFUNCTION LEVER
- 6.5.1. EXPLANATION OF COMPONENTS
- 6.5.2. OPERATION
- 6.6. JOYSTICK STEERING SYSTEM
- 6.6.1. COMPONENTS
- 6.6.2. STRUCTURE AND FUNCTION
- 6.6.3. GETTING IN OR OUT
- 6.6.4. ADJUSTMENT OF JOYSTICK CONSOLE
- 6.6.5. OPERATION METHOD OF JOYSTICK STEERING SYSTEM
- 6.7. EPC WORK EQUIPMENT LEVER
- 6.7.1. OPERATIONAL FEATURES
- 6.7.2. SWITCHES
- 6.7.3. SEMI AUTO DIGGING OPERATIONS
- 6.7.4. METHOD OF REMOTE POSITIONER
- 7. INDEX
- 7.1. INDEX
- 8. NOTES
- 8.1. NOTES
There are no reviews yet.