Description
-
Model List:
- WA600-6 Wheel Loader
- 1. Cover
- 2. CONTENTS
- 3. Block outline
- 4. Principal component dimension table
- 5. Work space layout
- 6. General assembly schedule
- 7. List of equipment, jigs, tools and consumables
- 8. Oil, grease and paints
- 9. Assembly procedure
- 9.1. Oil and coolant
- 9.2. Oil and coolant capacity
- 9.3. Setting the front axle and bare machine to stationary position
- 9.4. Installing the front axle
- 9.5. Connecting the drive shaft
- 9.6. Connecting the brake pipe
- 9.7. Connecting the brake pipe (Brake cooling specification)
- 9.8. Installing tire and rim assembly
- 9.9. Installing step
- 9.10. Installing cab (1)
- 9.11. Installing cab (2) (AJSS specification)
- 9.12. Installing cab (2) (Steering wheel specification)
- 9.13. Installing cab (2) (AJSS and steering wheel specification)
- 9.14. Installing cab (3)
- 9.15. Installing cab (4) (AJSS specification)
- 9.16. Installing cab (4) (Steering wheel specification)
- 9.17. Installing cab (5) (Steering wheel specification)
- 9.18. Installing cab (6) (AJSS and steering wheel specification)
- 9.19. Installing cab harness (1/2)
- 9.20. Installing cab harness (2/2)
- 9.21. Installing cab duct (1/3)
- 9.22. Installing cab duct (2/3)
- 9.23. Installing cab duct (3/3)
- 9.24. Installation of yellow rotary lamp
- 9.25. Installing front fender
- 9.26. Installing front light support and connection
- 9.27. Installing muffler stack and mirror
- 9.28. Installing counterweight (Standard and 1 ton heavier counterweight specifications)
- 9.29. Installing counterweight (Load and carry specification)
- 9.30. Installing pin (Standard and EU specifications)
- 9.31. Installing rear access ladder and L.H. platform
- 9.32. Installing the left handrail
- 9.33. Installing right platform and R.H. handrail
- 9.34. Installing fire extinguisher
- 9.35. Installing the rear fender mudguard plate
- 9.36. Installing rear fender
- 9.37. Installing cab undercover
- 9.38. Checking of sections
- 9.39. Air bleeding of work equipment hydraulic circuit and respective cylinders
- 9.40. Starting engine (1/2)
- 9.41. Starting engine (2/2)
- 9.42. Bleeding air from brake system
- 9.43. Installing lift arm and bell crank assembly
- 9.44. Connection of autogreasing boom piping (Autogreasing spec.)
- 9.45. Installing bucket cylinder (Bell crank side)
- 9.46. Installing bucket (1/3)
- 9.47. Installation of bucket (1) (Autogreasing spec.)
- 9.48. Installing bucket (2/3)
- 9.49. Installation of bucket (2) (Autogreasing spec.)
- 9.50. Installation of bucket (2) (Autogreasing spec.)
- 9.51. Installing bucket (3/3)
- 9.52. Greasing (1st time)
- 9.53. Greasing (1st time) Autogreasing spec.
- 9.54. Installing lift arm positioner
- 9.55. Contents of adjustment items
- 9.56. Setting of machine monitor
- 9.57. Adjustment of work equipment controller lift arm angle
- 9.58. Adjustment of work equipment EPC starting current (1/2)
- 9.59. Adjustment of work equipment EPC starting current (2/2)
- 9.60. Adjustment of bucket positioner (1/2)
- 9.61. Adjustment of bucket positioner (2/2)
- 9.62. Adjustment of load meter lift arm angle
- 9.63. Load meter noload calibration
- 9.64. Deleting the electrical system failure history (1/2)
- 9.65. Deleting the electrical system failure history (2/2)
- 9.66. Installing the floor mat (AJSS specification)
- 9.67. Installing the floor mat (Steering wheel specification)
- 9.68. Runningin procedure (1/2)
- 9.69. Runningin procedure (2/2)
- 9.70. Greasing (2nd time)
- 9.71. Greasing (2nd time) Autogreasing spec.
- 9.72. Adding grease with autogreasing pump Autogreasing spec.
- 9.73. Setting of autogreasing pump controller Autogreasing spec.
- 9.74. Touch up work
- 9.75. On use of starter kit (dummy harness) and precaution on its use
- 9.76. Starter kit (dummy harness) assembling procedure
- 10. Appendix Machine check sheet for field assembly
There are no reviews yet.