Description
-
Model List:
- WA600-6 Wheel Loader
- 1. Cover
- 2. Block outline
- 3. Principal component dimension table
- 4. Work space layout
- 5. General assembly schedule
- 6. List of equipment, jigs, tools and consumables
- 7. Oil, grease and paints
- 8. Assembly procedure
- 8.1. Oil and coolant
- 8.2. Oil and coolant capacity
- 8.3. Setting the front axle and bare machine to stationary position
- 8.4. Installing the front axle
- 8.5. Connecting the drive shaft
- 8.6. Connecting the brake pipe
- 8.7. Connecting the brake pipe (Brake cooling specification)
- 8.8. Installing tire and rim assembly
- 8.9. Installing step
- 8.10. Installing cab (1)
- 8.11. Installing cab (2) (AJSS specification)
- 8.12. Installing cab (2) (Steering wheel specification)
- 8.13. Installing cab (2) (AJSS and steering wheel specification)
- 8.14. Installing cab (3)
- 8.15. Installing cab (4) (AJSS specification)
- 8.16. Installing cab (4) (Steering wheel specification)
- 8.17. Installing cab (5) (Steering wheel specification)
- 8.18. Installing cab (6) (AJSS and steering wheel specification)
- 8.19. Installing cab harness (1/2)
- 8.20. Installing cab harness (2/2)
- 8.21. Installing cab duct (1/4)
- 8.22. Installing cab duct (2/4)
- 8.23. Installing cab duct (3/4)
- 8.24. Installing cab duct (4/4)
- 8.25. Installation of yellow rotary lamp
- 8.26. Installation of undercab cover
- 8.27. Installing front fender
- 8.28. Installing front light support and connection
- 8.29. Installing muffler stack and mirror
- 8.30. Installing counterweight (Standard and 1 ton heavier counterweight specifications)
- 8.31. Installing counterweight (Load and carry specification)
- 8.32. Installing pin (Standard and EU specifications)
- 8.33. Installing rear access ladder and L.H. platform
- 8.34. Installation of platform (R.H.) support
- 8.35. Installing the left handrail
- 8.36. Installing right platform and R.H. handrail
- 8.37. Installing fire extinguisher
- 8.38. Installing the rear fender mudguard plate
- 8.39. Installing rear fender
- 8.40. Installing cab undercover
- 8.41. Checking of sections
- 8.42. Air bleeding of work equipment hydraulic circuit and respective cylinders
- 8.43. Starting engine (1/2)
- 8.44. Starting engine (2/2)
- 8.45. Bleeding air from brake system
- 8.46. Installation of boom and bell crank assembly (Preparation for connection of bucket cylinder)
- 8.47. Installation of boom and bell crank assembly (Preparation for connection of lift cylinder)
- 8.48. Installation of boom and bell crank assembly (1)
- 8.49. Installation of boom and bell crank assembly (2)
- 8.50. Connection of autogreasing boom piping (Autogreasing spec.)
- 8.51. Preparation for connection of bucket cylinder
- 8.52. Installing bucket cylinder (Bell crank side)
- 8.53. Preparation for installation of bucket
- 8.54. Installation of bucket (1/3)
- 8.55. Installation of bucket (1) (Autogreasing spec.)
- 8.56. Installing bucket (2/3)
- 8.57. Installation of bucket (2) (Autogreasing spec.)
- 8.58. Installation of bucket (2) (Autogreasing spec.)
- 8.59. Installation of bucket (3/3)
- 8.60. Greasing (1st time)
- 8.61. Greasing (1st time) Autogreasing spec.
- 8.62. Installing lift arm positioner
- 8.63. Contents of adjustment items
- 8.64. Setting of machine monitor
- 8.65. Adjustment of work equipment controller lift arm angle
- 8.66. Adjustment of work equipment EPC starting current (1/2)
- 8.67. Adjustment of work equipment EPC starting current (2/2)
- 8.68. Adjustment of bucket positioner (1/2)
- 8.69. Adjustment of bucket positioner (2/2)
- 8.70. Adjustment of load meter lift arm angle
- 8.71. Load meter noload calibration
- 8.72. Deleting the electrical system failure history (1/2)
- 8.73. Deleting the electrical system failure history (2/2)
- 8.74. Installing the floor mat (AJSS specification)
- 8.75. Installing the floor mat (Steering wheel specification)
- 8.76. Runningin procedure (1/2)
- 8.77. Runningin procedure (2/2)
- 8.78. Greasing (2nd time)
- 8.79. Greasing (2nd time) Autogreasing spec.
- 8.80. Adding grease with autogreasing pump Autogreasing spec.
- 8.81. Setting of autogreasing pump controller Autogreasing spec.
- 8.82. Touch up work
- 8.83. On use of starter kit (dummy harness) and precaution on its use
- 8.84. Starter kit (dummy harness) assembling procedure
- 8.85. Check tire pressure and inflate tire
- 9. Appendix Machine check sheet for field assembly
There are no reviews yet.