Description
-
Model List:
- WA700-3 Galeo Wheel Loader
- 1. MAIN MENU
- 2. COVER
- 3. FOREWORD
- 3.1. FOREWORD
- 3.2. SAFETY INFORMATION
- 3.3. INTRODUCTION
- 3.3.1. FRONT/REAR, LEFT/RIGHT DIRECTIONS OF MACHINE
- 3.3.2. VISIBILITY FROM OPERATORS SEAT
- 3.4. NECESSARY INFORMATION
- 3.4.1. PRODUCT IDENTIFICATION NUMBER (PIN)/MACHINE SERIAL NO. PLATE
- 3.4.2. ENGINE SERIAL NO. PLATE AND POSITION
- 3.4.3. POSITION OF SERVICE METER
- 3.4.4. TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
- 4. CONTENTS
- 5. SAFETY
- 5.1. SAFETY
- 5.2. SAFETY LABELS
- 5.2.1. LOCATION OF SAFETY LABELS
- 5.3. GENERAL PRECAUTIONS
- 5.4. PRECAUTIONS FOR OPERATION
- 5.4.1. STARTING ENGINE
- 5.4.2. OPERATION
- 5.4.3. TRANSPORTATION
- 5.4.4. BATTERY
- 5.4.5. TOWING
- 5.5. PRECAUTIONS FOR MAINTENANCE
- 5.6. PRECAUTIONS WITH TIRES
- 6. OPERATION
- 6.1. GENERAL VIEW
- 6.1.1. GENERAL VIEW OF MACHINE
- 6.1.2. GENERAL VIEW OF CONTROLS AND GAUGES
- 6.2. EXPLANATION OF COMPONENTS
- 6.2.1. MACHINE MONITOR
- 6.2.2. SWITCHES
- 6.2.3. CONTROL LEVERS, PEDALS
- 6.2.4. MAIN MONITOR TILT LEVER
- 6.2.5. CAP WITH LOCK
- 6.2.6. FUEL STOP LEVER FOR EMERGENCY ENGINE STOP
- 6.2.7. SAFETY BAR
- 6.2.8. TOWING PIN
- 6.2.9. GREASE PUMP
- 6.2.10. BACKUP ALARM
- 6.2.11. CAB DOOR OPEN LOCK
- 6.2.12. AIR CONDITIONER
- 6.2.13. PRECAUTIONS WHEN HANDLING ACCUMULATOR
- 6.3. OPERATION
- 6.3.1. CHECK BEFORE STARTING ENGINE, ADJUST
- 6.3.2. STARTING ENGINE
- 6.3.3. OPERATIONS AND CHECKS AFTER STARTING ENGINE
- 6.3.4. STOPPING ENGINE
- 6.3.5. CHECK AFTER STOPPING ENGINE
- 6.3.6. MOVING THE MACHINE (DIRECTIONAL, SPEED), STOPPING THE MACHINE
- 6.3.7. TURNING
- 6.3.8. OPERATION OF WORK EQUIPMENT
- 6.3.9. WORK POSSIBLE USING WHEEL LOADER
- 6.3.10. ADJUSTING WORK EQUIPMENT POSTURE
- 6.3.11. REMOVAL AND INSTALLATION OF THE BUCKET
- 6.3.12. PARKING MACHINE
- 6.3.13. CHECKS AFTER COMPLETION OF OPERATION
- 6.3.14. LOCKING
- 6.3.15. HANDLING THE TIRES
- 6.4. TRANSPORTATION
- 6.4.1. TRANSPORTATION PROCEDURE
- 6.4.2. LOADING, UNLOADING WORK
- 6.4.3. METHOD OF SECURING MACHINE
- 6.4.4. METHOD OF LIFTING MACHINE
- 6.5. COLD WEATHER OPERATION
- 6.5.1. PRECAUTIONS FOR LOW TEMPERATURE
- 6.5.2. PRECAUTIONS AFTER COMPLETION OF WORK
- 6.5.3. AFTER COLD WEATHER
- 6.5.4. WARMINGUP OPERATION FOR STEERING HYDRAULIC CIRCUIT IN COLD WEATHER
- 6.6. LONGTERM STORAGE
- 6.6.1. BEFORE STORAGE
- 6.6.2. DURING STORAGE
- 6.6.3. AFTER STORAGE
- 6.7. TROUBLESHOOTING
- 6.7.1. WHEN MACHINE RUNS OUT OF FUEL
- 6.7.2. METHOD OF TOWING MACHINE
- 6.7.3. IF BATTERY IS DISCHARGED
- 6.7.4. OTHER TROUBLE
- 7. MAINTENANCE
- 7.1. GUIDES TO MAINTENANCE
- 7.2. OUTLINES OF SERVICE
- 7.2.1. HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC
- 7.2.2. OUTLINE OF ELECTRIC SYSTEM
- 7.3. WEAR PARTS
- 7.3.1. WEAR PARTS LIST
- 7.4. USE OF FUEL, COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
- 7.4.1. PROPER SELECTION OF FUEL, COOLANT AND LUBRICANTS
- 7.5. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
- 7.5.1. TORQUE LIST
- 7.6. PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
- 7.6.1. SAFETY CRITICAL PARTS
- 7.7. MAINTENANCE SCHEDULE CHART
- 7.7.1. MAINTENANCE SCHEDULE CHART
- 7.8. SERVICE PROCEDURE
- 7.8.1. INITIAL 250 HOURS SERVICE
- 7.8.2. INITIAL 2000 HOURS SERVICE
- 7.8.3. WHEN REQUIRED
- 7.8.4. CHECK BEFORE STARTING
- 7.8.5. EVERY 50 HOURS SERVICE
- 7.8.6. EVERY 100 HOURS SERVICE
- 7.8.7. EVERY 250 HOURS SERVICE
- 7.8.8. EVERY 500 HOURS SERVICE
- 7.8.9. EVERY 1000 HOURS SERVICE
- 7.8.10. EVERY 2000 HOURS SERVICE
- 7.8.11. EVERY 4000 HOURS SERVICE
- 8. SPECIFICATIONS
- 8.1. SPECIFICATIONS
- 9. ATTACHMENTS, OPTIONS
- 9.1. SELECTING BUCKET AND TIRES
- 9.2. HANDLING AUTOGREASING SYSTEM
- 9.2.1. METHOD OF OPERATING AUTOGREASING SYSTEM
- 9.2.2. PRECAUTIONS WHEN HANDLING AUTOGREASING SYSTEM
- 9.2.3. METHOD OF ADJUSTING DISCHARGE FROM INJECTOR
- 9.2.4. METHOD OF SETTING TIMER
- 9.3. CAR RADIO
- 9.3.1. EXPLANATION OF COMPONENTS
- 9.3.2. METHOD OF USE
- 9.3.3. PRECAUTIONS WHEN USING
- 9.4. AM/FM RADIOCASSETTE STEREO
- 9.4.1. EXPLANATION OF COMPONENTS
- 9.4.2. METHOD OF OPERATION
- 9.4.3. PRECAUTIONS FOR USE
- 10. INDEX
There are no reviews yet.