Linde 335-03 – E16C, E16P, E20P Production site Xiamen Operating Instructions SN 09.11 and up

Description

• Model List:
  • E16C
  • E16P
  • E20P

• 1. Electric forklift truckE16C03, E16P03, E20P03
• 1.1. Table of content
• 1.2. Introduction
• 1.2.1. Introduction
• 1.2.2. Intended use
• 1.2.3. Impermissible use
• 1.2.4. Description of use and climatic conditions
• 1.2.5. Symbols used
• 1.2.6. Technical description
• 1.2.7. Legal requirements for marketing
• 1.3. Safety
• 1.3.1. Safety guidelines
• 1.3.2. Residual risks
• 1.3.3. Stability
• 1.3.4. In the case of tipover
• 1.3.5. Handling consumables
• 1.3.6. Qualified person
• 1.3.7. Regulations
• 1.3.8. Fit attachments
• 1.3.9. Emergency exit with attached rear window
• 1.3.10. Manually tilting the mast and lowering the fork
• 1.3.11. Do not use cables to open the overhead guard by force
• 1.4. Overview of the forklift truck
• 1.4.1. Identification plate
• 1.4.2. Overview of the forklift truck
• 1.4.3. Operating devices
• 1.4.4. Display unit
• 1.5. Operation
• 1.5.1. Preuse daily checks and maintenance
• 1.5.1.1. Preshift checks
• 1.5.1.2. Opening the overhead guard
• 1.5.1.3. Checking the battery level
• 1.5.1.4. Battery change
• 1.5.1.5. Preuse daily checks and maintenance
• 1.5.1.6. Adjusting the drivers seat
• 1.5.2. Emergency off switch
• 1.5.3. Driving
• 1.5.4. Singlepedal operation (optional)
• 1.5.5. Steering system
• 1.5.6. Brake system
• 1.5.7. Operating the lift mast and attachments using the centralised control lever (joystick)
• 1.5.8. Single lever operation of the lift mast and attachments
• 1.5.9. Working spotlights, windscreen wipers, headlights,direction indicator lights
• 1.5.10. Horn, electrical system cover
• 1.5.11. Fuses
• 1.5.12. Before loading
• 1.5.13. Loading
• 1.5.14. Tow coupling
• 1.5.15. Truck transport
• 1.5.15.1. Towing regulations
• 1.5.15.2. Carrying and lifting the forklift truck
• 1.5.16. Wheel change
• 1.5.17. Use in cold stores
• 1.5.18. Truck storage
• 1.5.18.1. Taking the forklift truck out of operation
• 1.5.19. Disposal of old trucks
• 1.6. Maintenance
• 1.6.1. Summary
• 1.6.2. Working on the lift mast or front section of the fork lift truck
• 1.6.3. Inspection and maintenance parameters
• 1.6.4. Recommended lubricants
• 1.6.5. hour maintenance plan
• 1.6.6. hour maintenance plan
• 1.6.7. Reduction gearbox
• 1.6.7.1. Checking the wheel gear oil level
• 1.6.7.2. Checking whether the speed reduction gearbox is leaking
• 1.6.7.3. Cleaning both sides of the traction motor, the power steering and working hydraulic pump motor
• 1.6.7.4. Replacing the gear oil in the speed reduction gearbox
• 1.6.8. Frame and installation
• 1.6.8.1. Checking the counterweight, motors, chassis, speed reduction gearbox, overhead guard and steering axle fastenings
• 1.6.8.2. Lubricating the overhead guard pin shaft
• 1.6.8.3. Checking and lubricating other pins and swivel points
• 1.6.8.4. Checking the status of the antistatic belts (only for trucks fitted with super clean tyres)
• 1.6.9. Chassis frame
• 1.6.9.1. Check the brake system
• 1.6.9.2. Tighten the wheel nuts
• 1.6.9.3. Cleaning.lubricating the steering axle
• 1.6.9.4. Replacing the brake fluid
• 1.6.10. Operating devices
• 1.6.10.1. Checking the joystick pad
• 1.6.10.2. Checking and lubricating the pedal mechanisms, control linkage mechanisms and the overhead guard locking devices
• 1.6.11. Electrical system
• 1.6.11.1. Checking the status and tightness of the electrical cables, electrical connections and plug connectors
• 1.6.11.2. (As required) Clean the power modules of the traction and lift controls, the fans and the radiator housing with compressed air
• 1.6.11.3. Cleaning the digital control cables
• 1.6.11.4. Inspect the contactor contacts, and replace if necessary
• 1.6.12. Hydraulic system
• 1.6.12.1. Check the hydraulic oil level
• 1.6.12.2. Checking the leak resistance of the working and steering hydraulic systems
• 1.6.12.3. Replacing the air, pressure and suction filters
• 1.6.12.4. Replacing the hydraulic oil (if it is Bio hydraulic oil, the Aral Forbex SE46 is 6000operating hours)
• 1.6.13. Load lift system
• 1.6.13.1. Checking the condition, tightness and function of the lift mast, lift chains and stop block
• 1.6.13.2. Adjusting the length of the lift chains, and lubricating using chain spray
• 1.6.13.3. Checking the trucks releasing and locking equipment
• 1.7. Technical data
• 1.7.1. List of technical parameter marks
• 1.7.2. Technical parameters E16C forklift
• 1.7.3. Technical parameters E16P forklift
• 1.7.4. Technical parameters E20P forklift
• 1.7.5. Lift mast data
• 1.8. Circuit diagrams
• 1.8.1. Electrical circuit diagram
• 1.8.1.1. Circuit diagrams
• 1.8.1.2. Circuit diagrams
• 1.8.1.3. Circuit diagrams
• 1.8.2. Hydraulic oil diagram
• 1.8.2.1. Working and steering hydraulic system circuit diagrams
• 1.8.2.2. Working and steering hydraulic system circuit diagrams
• 2. Operating Instruction (DataLogger)