Komatsu 730E Dump Truck Operation and Maintenance Manual CEAD014800

Komatsu 730E Dump Truck Operation and Maintenance Manual CEAD014800 - Image 2

Komatsu 730E Dump Truck Operation and Maintenance Manual CEAD014800 - Image 3

Komatsu 730E Dump Truck Operation and Maintenance Manual CEAD014800 - Image 4

Komatsu 730E Dump Truck Operation and Maintenance Manual CEAD014800 - Image 5

komatsu 730e dump truck operation and maintenance manual cead014800 2

komatsu 730e dump truck operation and maintenance manual cead014800 3 2

Komatsu 730E Dump Truck Operation and Maintenance Manual CEAD014800

$30.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: CEAD014800
Format: PDF
Size: 2.7MB
Number of Pages: 142

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- 730E Dump Truck

0.1. TABLE OF CONTENTS
0.2. TRUCK MODEL ILLUSTRATION
0.3. ABOUT THIS MANUAL
0.4. STANDARD CHARTS AND TABLES
1. SAFETY
1.1. GENERAL SAFETY
1.2. PRECAUTIONS DURING OPERATION
1.2.1. BEFORE STARTING ENGINE
1.2.2. OPERATING MACHINE
1.2.3. BATTERY
1.2.4. TOWING
1.3. PRECAUTIONS FOR MAINTENANCE
1.3.1. BEFORE CARRYING OUT MAINTENANCE
1.3.2. DURING MAINTENANCE
1.3.3. TIRES
1.4. ADDITIONAL JOB SITE RULES
1.5. WHEN REPAIRS ARE NECESSARY
1.6. WARNINGS AND CAUTIONS
2. OPERATION
2.1. OPERATING INSTRUCTIONS
2.1.1. Preparing for Operation
2.1.2. Safety is Thinking Ahead
2.1.3. At The Truck Ground Level Walk Around Inspection
2.2. ENGINE STARTUP SAFETY PRACTICES
2.3. AFTER ENGINE HAS STARTED
2.4. MACHINE OPERATION SAFETY PRECAUTIONS
2.5. SAFE PARKING PROCEDURES
2.6. ENGINE SHUTDOWN PROCEDURE
2.7. DELAYED ENGINE SHUTDOWN PROCEDURE
2.8. SUDDEN LOSS OF POWER
2.9. OPERATOR CAB AND CONTROLS
2.9.1. STEERING WHEEL AND CONTROLS
2.9.2. SERVICE BRAKE PEDAL
2.9.3. DYNAMIC RETARDER PEDAL
2.9.4. THROTTLE PEDAL
2.9.5. HEATER / AIR CONDITIONER VENTS
2.9.6. HEATER / AIR CONDITIONER COMPARTMENT AND CONTROLS
2.9.7. OVER HEAD PANEL AND DISPLAYS
2.9.8. CENTER CONSOLE
2.9.9. OPERATOR SEAT
2.10. INSTRUMENT PANEL AND INDICATOR LIGHTS
2.10.1. Control Symbols
2.11. INSTRUMENT PANEL
2.12. PANEL GAUGES, INDICATORS, AND CONTROLS (Figure 311)
2.13. OVERHEAD STATUS / WARNING INDICATOR LIGHT PANEL
2.14. INDICATOR LIGHT SYMBOLS
2.14.1. HAZARD WARNING LIGHTS
2.14.2. LAMP TEST SWITCH / Centry Diagnostic Test Switch
2.15. CENTRY FUEL SYSTEM DIAGNOSTICS
2.15.1. DETERMINING FAULT CODES
2.15.2. EXITING THE DIAGNOSTICS MODE
3. MAINTENANCE
3.1. LUBRICATION AND SERVICE
3.1.1. SERVICE CAPACITIES
3.1.2. HYDRAULIC TANK SERVICE
3.1.3. COOLANT LEVEL CHECK
3.1.4. RADIATOR FILLING PROCEDURE
3.1.5. COOLING SYSTEM RECOMMENDATIONS
3.1.6. LUBRICATION CHART
3.1.7. HOUR (SHIFT) LUBRICATION AND MAINTENANCE CHECKS
3.1.8. HOUR LUBRICATION AND MAINTENANCE CHECKS
3.1.9. HOUR LUBRICATION AND MAINTENANCE CHECKS
3.1.10. HOUR LUBRICATION AND MAINTENANCE CHECKS
3.1.11. HOUR LUBRICATION AND MAINTENANCE CHECKS
3.1.12. HOUR LUBRICATION AND MAINTENANCE CHECKS
3.1.13. HOUR LUBRICATION AND MAINTENANCE CHECKS
3.2. LINCOLN AUTOMATIC LUBRICATION SYSTEM
3.2.1. GENERAL DESCRIPTION
3.2.2. SYSTEM COMPONENTS
3.2.3. SYSTEM OPERATION
3.2.4. GENERAL INSTRUCTIONS
3.2.4.1. SYSTEM PRIMING
3.2.4.2. LUBRICANT PUMP
3.2.4.3. FILTER AND RESERVOIR
3.2.4.4. INJECTORS
3.2.5. SYSTEM CHECKOUT
3.2.6. VDC SOLID STATE TIMER CHECKOUT ADJUSTMENT
3.2.7. PUMP REBUILD
3.2.7.1. DISASSEMBLY
3.2.7.2. CLEANING AND INSPECTION
3.2.7.3. ASSEMBLY
3.2.8. PREVENTATIVE MAINTENANCE PROCEDURE
4. SPECIFICATIONS
4.1. MAJOR COMPONENT DESCRIPTION
4.2. SPECIFICATIONS
5. OPTIONAL EQUIPMENT
5.1. PAYLOAD METER III TM
5.1.1. INDEX
5.1.1.1. OPERATION SECTION
5.1.1.2. Introduction
5.1.1.3. Data Summary
5.1.1.4. Data Gathering
5.1.1.5. Component Description
5.1.1.5.1. System Diagram
5.1.1.5.2. Suspension Pressure Sensors
5.1.1.5.3. Inclinometer
5.1.1.5.4. Operator Display
5.1.1.5.5. Operator Switch
5.1.1.5.6. Speed Input
5.1.1.5.7. BodyUp Switch
5.1.1.5.8. Brake Lock Switch
5.1.1.5.9. Payload Meter
5.1.1.5.10. Communications Ports
5.1.1.5.11. Keyswitch Input
5.1.1.5.12. Payload Meter Power
5.1.1.5.13. Load Lights
5.1.1.5.14. Wiring and Termination
5.1.1.5.15. TCI Outputs
5.1.1.6. Operators Display and Switch
5.1.1.6.1. Reading the Speedometer
5.1.1.6.2. Reading the Load Display
5.1.1.6.3. Using the Operator ID
5.1.1.6.4. Using the Load and Ton Counter
5.1.1.6.4.1. Total Ton Counter
5.1.1.6.4.2. Total Load Counter
5.1.1.6.4.3. Clearing the Counters
5.1.1.6.5. Viewing Live Sensor Data
5.1.1.6.6. Other Display Messages
5.1.1.7. Payload Operation Calculation
5.1.1.7.1. Description of Haul Cycle States
5.1.1.7.1.1. Haul Cycle Description
5.1.1.7.2. Load Calculation
5.1.1.7.3. Carry Back
5.1.1.7.4. Measurement Accuracy
5.1.1.7.5. Sources for Payload Error
5.1.1.7.5.1. Payload Error
5.1.1.7.5.2. Loading Conditions
5.1.1.7.5.3. Pressure Sensors
5.1.1.7.5.4. Swingloads
5.1.1.7.5.5. Speed and Distance
5.1.1.8. HAUL CYCLE DATA
5.1.1.8.1. Haul Cycle Data
5.1.1.8.2. Haul Cycle Warning Flags
5.1.1.8.3. Alarm Records
5.1.1.8.4. Frame Torque Data
5.1.1.8.5. Sprung Weight Data
5.1.1.8.6. Maximum Speed Data
5.1.1.9. PC Software Overview
5.1.1.9.1. PC Overview
5.1.1.9.2. System Configuration
5.1.1.9.3. Installing the PLMIII Software
5.1.1.10. Downloading Data
5.1.1.11. PLMIII System Configuration
5.1.1.11.1. Starting Communications
5.1.1.11.1.1. Displayed Payload Units
5.1.1.11.1.2. Time Units
5.1.1.11.2. Connection Menu
5.1.1.11.3. Connecting to the Payload Meter
5.1.1.11.4. Configure the Payload Meter
5.1.1.11.4.1. Setting the Date and Time
5.1.1.11.4.2. Setting the Truck Type
5.1.1.11.4.3. Setting the Gauge Display Units
5.1.1.11.4.4. Setting the Frame Serial Number
5.1.1.11.4.5. Setting the Truck Number
5.1.1.11.4.6. Setting the Komatsu Distributor
5.1.1.11.4.7. Setting the Komatsu Customer
5.1.1.11.5. Clean Truck Tare
5.1.1.11.6. Inclinometer Calibration
5.1.1.12. Data Analysis
5.1.1.12.1. Creating a Query
5.1.1.12.1.1. Sorting on Truck Unit Number
5.1.1.12.1.2. Sorting on Truck Type
5.1.1.12.1.3. Sorting on Date Range
5.1.1.12.1.4. Sorting on Time Range
5.1.1.12.2. Payload Detail Screen
5.1.1.12.3. Creating Reports
5.1.1.12.3.1. Summary one page report
5.1.1.12.3.2. Detailed multipage report
5.1.1.12.4. Creating Graphs
5.1.1.12.5. To export data in ZIP format
5.1.1.12.6. Importing Data
5.1.1.12.7. Deleting Haul Cycle Records
5.1.1.12.8. Viewing Alarms
5.1.1.12.9. Deleting Alarm Records
5.2. RADIO, AM / FM STEREO CASSETTE

Rate this product