Description
-
Model List:
- PC100-6 Mighty Hydraulic Excavator
- PC100L-6 Mighty Hydraulic Excavator
- PC120-6 Mighty Hydraulic Excavator
- PC120LC-6 Mighty Hydraulic Excavator
- PC130-6 Mighty Hydraulic Excavator
- 1. COVER
- 2. FOREWORD
- 3. SAFETY INFORMATION
- 4. INTRODUCTION
- 5. LOCATION OF PLATES, TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
- 6. CONTENTS
- 7. SAFETY
- 7.1. GENERAL PRECAUTIONS
- 7.2. PRECAUTIONS DURING OPERATION
- 7.2.1. BEFORE STARTING ENGINE
- 7.2.2. AFTER STARTING ENGINE
- 7.2.3. TRANSPORTATION
- 7.2.4. BATTERY
- 7.2.5. TOWING
- 7.2.6. BUCKET WITH HOOK
- 7.3. PRECAUTIONS FOR MAINTENANCE
- 7.3.1. BEFORE CARRYING OUT MAINTENANCE
- 7.3.2. DURING MAINTENANCE
- 7.4. POSITION FOR ATTACHING SAFETY LABELS
- 8. OPERATION
- 8.1. GENERAL VIEW
- 8.1.1. GENERAL VIEW OF MACHINE
- 8.1.2. GENERAL VIEW OF CONTROLS AND GAUGES
- 8.2. EXPLANATION OF COMPONENTS
- 8.2.1. MACHINE MONITOR
- 8.2.2. SWITCHES
- 8.2.3. CONTROL LEVERS, PEDALS
- 8.2.4. CEILING WINDOW
- 8.2.5. FRONT WINDOW
- 8.2.6. DOOR LOCK
- 8.2.7. CAP, COVER WITH LOCK
- 8.2.8. HOT/COOL BOX
- 8.2.9. LUGGAGE BOX
- 8.2.10. ASHTRAY
- 8.2.11. AIR CONDITIONER
- 8.2.12. CAR RADIO
- 8.2.13. ELECTRIC POWER SOURCE
- 8.2.14. FUSE
- 8.2.15. FUSIBLE LINK
- 8.2.16. CONTROLLERS
- 8.2.17. TOOL BOX
- 8.2.18. GREASE PUMP HOLDER
- 8.3. OPERATION
- 8.3.1. CHECK BEFORE STARTING ENGINE
- 8.3.2. STARTING ENGINE
- 8.3.3. OPERATIONS AND CHECKS AFTER STARTING ENGINE
- 8.3.4. MOVING MACHINE OFF
- 8.3.5. STEERING MACHINE
- 8.3.6. STOPPING MACHINE
- 8.3.7. SWINGING
- 8.3.8. OPERATION OF WORK EQUIPMENT
- 8.3.9. WORKING MODE SELECTION
- 8.3.10. HANDLING ACTIVE MODE
- 8.3.11. PROHIBITIONS FOR OPERATION
- 8.3.12. PRECAUTIONS FOR OPERATION
- 8.3.13. PRECAUTIONS WHEN TRAVELING UP OR DOWN HILLS
- 8.3.14. HOW TO ESCAPE FROM MUD
- 8.3.15. WORK POSSIBLE USING HYDRAULIC EXCAVATOR
- 8.3.16. REPLACEMENT AND INVERSION OF BUCKET
- 8.3.17. PARKING MACHINE
- 8.3.18. CHECK AFTER FINISHING WORK
- 8.3.19. STOPPING ENGINE
- 8.3.20. CHECK AFTER STOPPING ENGINE
- 8.3.21. LOCKING
- 8.3.22. HANDLING ROAD LINER (ROAD LINER ONLY)
- 8.4. TRANSPORTATION
- 8.4.1. LOADING, UNLOADING WORK
- 8.4.2. PRECAUTIONS FOR LOADING
- 8.4.3. PRECAUTIONS FOR TRANSPORTATION
- 8.5. COLD WEATHER OPERATION
- 8.5.1. PRECAUTIONS FOR LOW TEMPERATURE
- 8.5.2. PRECAUTIONS AFTER COMPLETION OF WORK
- 8.5.3. AFTER COLD WEATHER
- 8.6. LONGTERM STORAGE
- 8.6.1. BEFORE STORAGE
- 8.6.2. DURING STORAGE
- 8.6.3. AFTER STORAGE
- 8.6.4. STARTING MACHINE AFTER LONGTERM STORAGE
- 8.7. TROUBLESHOOTING
- 8.7.1. WHEN MACHINE RUNS OUT OF FUEL
- 8.7.2. PHENOMENA THAT ARE NOT FAILURES
- 8.7.3. METHOD OF TOWING MACHINE
- 8.7.4. USING METHOD FOR LIGHTWEIGHT TOWING HOOK
- 8.7.5. PRECAUTIONS ON PARTICULAR JOBSITES
- 8.7.6. IF BATTERY IS DISCHARGED
- 8.7.7. OTHER TROUBLE
- 9. MAINTENANCE
- 9.1. GUIDES TO MAINTENANCE
- 9.2. OUTLINES OF SERVICE
- 9.2.1. HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC
- 9.2.2. OUTLINE OF ELECTRIC SYSTEM
- 9.2.3. OUTLINE OF HYDRAULIC SYSTEM
- 9.3. WEAR PARTS LIST
- 9.4. RECOMMENDED FUEL, COOLANT, AND LUBRICANT
- 9.4.1. USE OF FUEL,COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
- 9.4.2. RECOMMENDED BRANDS, RECOMMENDED QUALITY FOR PRODUCTS OTHER THAN KOMATSU GENUINE OIL
- 9.5. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
- 9.5.1. INTRODUCTION OF NECESSARY TOOLS
- 9.5.2. TORQUE LIST
- 9.6. PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
- 9.7. MAINTENANCE SCHEDULE CHART
- 9.7.1. MAINTENANCE SCHEDULE CHART
- 9.7.2. MAINTENANCE INTERVAL WHEN USING HYDRAULIC BREAKER
- 9.8. SERVICE PROCEDURE
- 9.8.1. INITIAL 250 HOURS SERVICE
- 9.8.2. WHEN REQUIRED
- 9.8.3. CHECK BEFORE STARTING
- 9.8.4. EVERY 50 HOURS SERVICE
- 9.8.5. EVERY 100 HOURS SERVICE
- 9.8.6. EVERY 250 HOURS SERVICE
- 9.8.7. EVERY 500 HOURS SERVICE
- 9.8.8. EVERY 1000 HOURS SERVICE
- 9.8.9. EVERY 2000 HOURS SERVICE
- 9.8.10. EVERY 4000 HOURS SERVICE
- 9.8.11. EVERY 5000 HOURS SERVICE
- 10. SPECIFICATIONS
- 10.1. SPECIFICATIONS
- 11. OPTIONS, ATTACHMENTS
- 11.1. GENERAL PRECAUTIONS
- 11.1.1. PRECAUTIONS RELATED TO SAFETY
- 11.1.2. PRECAUTIONS WHEN INSTALLING ATTACHMENTS
- 11.2. HANDLING BUCKET WITH HOOK
- 11.2.1. CHECKING FOR DAMAGE TO BUCKET WITH HOOK
- 11.2.2. PROHIBITED OPERATIONS
- 11.2.3. PRECAUTIONS DURING OPERATIONS
- 11.3. USING SEAT BELT
- 11.3.1. SEAT BELT
- 11.4. HANDLING CAR HEATER
- 11.4.1. EXPLANATION OF COMPONENTS
- 11.4.2. PREPARING CAR HEATER
- 11.5. MACHINES READY FOR ATTACHMENTS
- 11.5.1. GENERAL LOCATIONS
- 11.5.2. HYDRAULIC CIRCUIT
- 11.5.3. OPERATION
- 11.5.4. HANDLING ACCUMULATOR
- 11.5.5. LONGTERM STORAGE
- 11.5.6. SPECIFICATIONS
- 11.6. INTRODUCTION OF OPTIONAL PARTS AND ATTACHMENTS
- 11.6.1. INTRODUCTION OF OPTIONAL PARTS AND ATTACHMENTS
- 11.6.2. ATTACHMENT INSTALLATION COMBINATION TABLE
- 11.6.3. SELECTION OF TRACK SHOES
- 11.6.4. HANDLING ROAD LINER
- 11.6.5. HANDLING AUTOMATIC GREASING CONTROLLER
- 11.7. EXTENDING MACHINE SERVICE LIFE
- 11.7.1. HYDRAULIC BREAKER
- 11.7.2. POWER RIPPER
- 11.7.3. FORK GRAB
- 11.7.4. GRAPPLE BUCKET
- 11.7.5. SCRAP GRAPPLE
- 11.7.6. CRUSHER AND SMASHER
- 11.7.7. HYDRAULIC PILE DRIVER
- 11.7.8. HYDRAULIC EXCAVATOR WITH MULTIPURPOSE CRANE
Reviews
There are no reviews yet.