Komatsu PC210i-10, PC210LCi-10 Hydraulic Excavator Operation and Maintenance Manual TEN00729-01

Description

• Model List:
  • PC210i-10 Hydraulic Excavator
  • PC210LCi-10 Hydraulic Excavator

• 1. Cover
• 2. FOREWORD
• 2.1. BEFORE READING THIS MANUAL
• 2.2. SAFETY INFORMATION
• 2.3. INTRODUCTION
• 2.3.1. USE OF MACHINE
• 2.4. CONTENTS
• 3. SAFETY
• 3.1. SAFETY
• 3.2. SAFETY LABELS
• 3.2.1. LOCATION OF SAFETY LABELS
• 3.2.2. SAFETY LABELS
• 3.3. GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTENANCE
• 3.3.1. STARTING ENGINE
• 3.4. PRECAUTIONS FOR OPERATION
• 3.4.1. PRECAUTIONS FOR CONTROL BOX
• 3.4.2. PRECAUTIONS FOR SEMIAUTO MODE
• 3.5. TRANSPORTATION
• 3.5.1. SAFETY RULES FOR LOADING AND UNLOADING
• 4. OPERATION
• 4.1. GENERAL VIEW
• 4.1.1. GENERAL VIEW OF MACHINE
• 4.1.2. GENERAL VIEW OF CAB
• 4.2. EXPLANATION OF COMPONENTS
• 4.2.1. WARNING DISPLAY
• 4.2.2. ACTION LEVEL MONITOR
• 4.2.3. OCCURRED ERROR LIST DISPLAY SWITCH
• 4.2.4. ALARM MONITOR LIST
• 4.2.5. SWITCHES
• 4.2.6. CONTROL LEVERS AND PEDALS
• 4.2.7. OPEN AND CLOSE CAB FRONT WINDOW
• 4.2.8. CUP HOLDER
• 4.2.9. HANDLING RADIO
• 4.2.10. AUXILIARY ELECTRIC POWER
• 4.2.11. FUSE
• 4.3. START CONTROL BOX
• 4.4. STOP CONTROL BOX
• 4.5. MACHINE OPERATIONS AND CONTROLS
• 4.5.1. CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE
• 4.5.2. STARTING ENGINE
• 4.5.3. STOPPING ENGINE
• 4.5.4. PROHIBITED OPERATIONS
• 4.5.5. RULES FOR OPERATION
• 4.5.6. PARKING MACHINE
• 4.6. TRANSPORTATION
• 4.6.1. REMOVE AND INSTALL GNSS ANTENNA
• 4.6.2. REMOVE AND INSTALL HANDRAIL
• 4.6.3. REMOVE AND INSTALL CAB PARTS
• 4.6.4. PROTECT CONNECTORS OF GNSS ANTENNA CABLE
• 4.7. LONGTERM STORAGE
• 4.7.1. STARTING MACHINE AFTER LONGTERM STORAGE
• 4.8. TROUBLES AND ACTIONS
• 4.8.1. IF ERROR INFORMATION IS DISPLAYED ON CONTROL BOX
• 4.8.2. OTHER TROUBLE
• 5. MAINTENANCE
• 5.1. MAINTENANCE SCHEDULE TABLE
• 5.1.1. EVERY 500 HOURS MAINTENANCE
• 5.2. MAINTENANCE PROCEDURE
• 5.2.1. EVERY 500 HOURS MAINTENANCE
• 6. SPECIFICATIONS
• 6.1. SPECIFICATIONS
• 7. ATTACHMENTS AND OPTIONS
• 7.1. RECOMMENDED ATTACHMENT OPERATIONS
• 7.1.1. HYDRAULIC BREAKER
• 8. SETTING
• 8.1. INTRODUCTION
• 8.1.1. CONTROL BOX
• 8.1.2. MACHINE MONITOR
• 8.2. CONTROL BOX
• 8.2.1. MENU
• 8.3. MACHINE MONITOR
• 8.3.1. MC SETTING
• 9. EXECUTIONS
• 9.1. SEMIAUTO MODE
• 9.1.1. PRECAUTIONS FOR OPERATION
• 9.1.2. PRECAUTIONS FOR REPLACING PARTS AND FAILURES
• 9.1.3. EXPLANATION ABOUT WORK MODE
• 9.1.4. SEMIAUTO MODE SETTING
• 9.2. TRAVEL MODE
• 9.2.1. TRAVEL MODE SETTINGS
• 9.2.2. SCREEN DISPLAY
• 9.2.3. SURFACE ELEVATION ADJUSTMENT MENU
• 9.2.4. TEMP. DESIGN MENU
• 9.2.5. TARGET SURFACE SETTINGS
• 9.3. ROUGH DIGGING MODE
• 9.3.1. ROUGH DIGGING SCREEN SETTINGS
• 9.4. FINISH DIGGING MODE
• 9.4.1. FINE DIGGING MODE SETTINGS
• 9.5. TARGET SURFACE OPERATIONS
• 9.5.1. TARGET SURFACE OPERATIONS MENU
• 9.5.2. TARGET SURFACE OPERATIONS PROCEDURE
• 9.6. BLADE EDGE POSITION
• 9.6.1. DISPLAY BLADE EDGE POSITION
• 9.6.2. COMPARE WITH BENCHMARK
• 9.6.3. ADJUST BLADE EDGE POSITION
• 9.7. DAILY CALIBRATION
• 9.7.1. WALKAROUND CHECKS OF INTELLIGENT MACHINE CONTROL EQUIPMENT
• 9.8. CHECK GNSS COMMUNICATION STATUS
• 9.8.1. OPERATION METHOD
• 9.8.2. CHECK SATELLITE NUMBER AND POSITIONING ERROR (FIX)
• 9.8.3. DISPLAY BUCKET EDGE COORDINATES (POSITION)
• 9.8.4. DISPLAY SATELLITE POSITION AND ELEVATION SETTINGS (SATELLITE)
• 9.8.5. INFORMATION OF GNSS RECEIVER (INFO)
• 9.8.6. EXPECTANCY OF EDGE ACCURANCY (PLANNING)
• 9.8.7. GLONASS SATELLITE SETTINGS (ADVANCED)
• 9.8.8. TILT SENSOR SETTINGS
• 9.9. PERFORM TOPO SURVEY
• 9.9.1. PERFORM TOPO SURVEY MANUALLY
• 9.9.2. PERFORM AUTOTOPO SURVEY
• 9.9.3. RESET TOPO SURVEY DEACTIVATION
• 9.10. TROUBLE SHOOTING
• 10. INDEX