Komatsu D65PXi-18 Bull Dozer Operation and Maintenance Manual TEN00772-01

Description

• Model List:
  • D65PXi-18 Bull Dozer

• 1. FOREWORD
• 1.1. READ THIS MANUAL
• 1.2. SAFETY INFORMATION
• 1.3. INTRODUCTION
• 1.3.1. MACHINE FEATURES
• 1.4. PRODUCT INFORMATION
• 1.4.1. LOCATION OF TRANSMITTER (TX.UNIT) PLATE
• 1.4.2. LOCATION OF RECEIVER (RX.UNIT) PLATE
• 1.4.3. LOCATION OF CONTROLLER (CR720) PLATE
• 1.5. TABLE OF CONTENTS
• 2. SAFETY
• 2.1. SAFETY
• 2.2. SAFETY LABELS
• 2.2.1. LOCATION OF SAFETY LABELS
• 2.2.2. CONTENTS OF SAFETY LABELS
• 2.3. GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTENANCE
• 2.4. PRECAUTIONS FOR OPERATION
• 2.4.1. START ENGINE
• 2.4.1.1. PRECAUTIONS BEFORE RADIO CONTROL OPERATION
• 2.4.1.2. INSTALL AND CHECK RADIO CONTROL TRANSMITTER
• 2.4.1.3. PRECAUTIONS WHEN TURNING ON POWER SUPPLY OF TRANSMITTER
• 2.4.1.4. PRECAUTIONS WHEN STARTING ENGINE
• 2.4.1.5. CHECKS AFTER ENGINE STARTED
• 2.4.2. PRECAUTIONS FOR OPERATION
• 2.4.2.1. PRECAUTIONS FOR TRAVELING WITH RADIO CONTROL
• 2.5. PRECAUTIONS FOR MAINTENANCE
• 2.5.1. PRECAUTIONS FOR CHECK AND MAINTENANCE
• 3. OPERATION
• 3.1. GENERAL VIEW
• 3.1.1. MACHINE EQUIPMENT NAME
• 3.2. EXPLANATION OF COMPONENTS
• 3.2.1. RADIO CONTROL DEVICE
• 3.2.1.1. TRANSMITTER (TX.UNIT)
• 3.2.1.2. RECEIVER (RX.UNIT)
• 3.2.1.3. CONTROLLER FOR RADIO CONTROL
• 3.2.1.4. RADIO CONTROL/ONBOARD SELECTOR SWITCH
• 3.2.1.5. FUSE
• 3.2.1.6. REVOLVING LAMP
• 3.2.1.7. PRECAUTIONS FOR USING intelligent Machine Control FUNCTION
• 3.3. HANDLE RADIO CONTROL UNIT
• 3.3.1. CHECKS BEFORE STARTING ENGINE
• 3.3.2. WALKAROUND CHECK
• 3.3.3. CHECKS BEFORE STARTING
• 3.3.3.1. METHOD FOR CHECKING HORN OPERATION
• 3.3.3.2. CHECK REVOLVING LAMP
• 3.3.3.3. CHECK TRANSMITTER, RECEIVER AND CONTROLLER
• 3.3.3.4. CHECK EMERGENCY STOP SWITCH
• 3.3.3.5. CHECK KEY SWITCH (OFF)
• 3.3.4. PRECAUTIONS WHEN HANDLING TRANSMITTER
• 3.3.5. PROCEDURE FOR STARTING ENGINE AND OPERATION BY RADIO CONTROL
• 3.3.6. PRECAUTIONS FOR OPERATION BY RADIO CONTROL
• 3.3.7. OPERATE BY RADIO CONTROL
• 3.3.7.1. METHOD FOR MOVING MACHINE
• 3.3.7.2. METHOD FOR STEERING (CHANGE THE DIRECTION) MACHINE
• 3.3.7.3. METHOD FOR OPERATING WORK EQUIPMENT
• 3.3.7.4. METHOD FOR ACCELERATION AND DECELERATION
• 3.3.7.5. METHOD FOR STOPPING MACHINE
• 3.3.8. PRECAUTIONS WHEN HANDLING RADIO CONTROL UNIT
• 3.3.8.1. PRECAUTIONS WHEN HANDLING TRANSMITTER
• 3.3.8.2. PRECAUTIONS WHEN HANDLING RECEIVER AND CONTROLLER
• 3.3.8.3. PRECAUTIONS FOR ONBOARD OPERATION
• 3.3.9. PROCEDURE FOR STOPPING OPERATION BY RADIO CONTROL
• 3.4. TRANSPORTATION
• 3.4.1. TRAVEL ON ROAD
• 3.4.2. PRECAUTIONS FOR TRANSPORTING MACHINE
• 3.4.3. TRANSPORTATION PROCEDURE
• 3.4.4. METHOD FOR INSTALLING RADIO CONTROL ANTENNA LATERALLY
• 3.4.5. METHOD FOR INSTALLING RADIO CONTROL ANTENNA LONGITUDINALLY
• 3.4.6. METHOD FOR REMOVING RADIO CONTROL OPERATION LAMP ASSEMBLY
• 3.4.7. METHOD FOR INSTALLING RADIO CONTROL OPERATION LAMP ASSEMBLY
• 3.4.8. METHOD FOR REMOVING RADIO CONTROL ANTENNA
• 3.4.9. METHOD FOR INSTALLING RADIO CONTROL ANTENNA
• 3.4.10. METHOD FOR REMOVING REVOLVING LAMP
• 3.4.11. METHOD FOR INSTALLING REVOLVING LAMP
• 3.5. TROUBLES AND ACTIONS
• 3.5.1. OTHER TROUBLE
• 4. MAINTENANCE
• 4.1. MAINTENANCE SCHEDULE
• 4.1.1. MAINTENANCE SCHEDULE TABLE
• 4.2. MAINTENANCE PROCEDURE
• 4.2.1. WHEN REQUIRED
• 4.2.1.1. METHOD FOR LUBRICATING BRAKE LINK
• 5. SPECIFICATIONS
• 5.1. SPECIFICATIONS
• 5.1.1. SPECIFICATIONS D65PXI18 RADIO CONTROL SPEC
• 5.2. SPECIFICATION
• 6. INDEX