Komatsu WA150-5H Wheel Loader Operation and Maintenance Manual VEAM934100

Description

• Model List:
  • WA150-5H Wheel Loader

• 1. MAIN MENU
• 2. COVER
• 3. Foreword
• 3.1. Foreword
• 3.1.1. EU Directives
• 3.2. Safety information
• 3.2.1. Signal words
• 3.2.2. Safety labels
• 3.3. Introduction
• 3.3.1. Intended use
• 3.3.2. Directions of machine
• 3.4. Necessary information
• 3.4.1. PIN/Machine serial no. plate and position
• 3.4.2. Engine serial no. plate and position
• 3.4.3. ROPS/FOPSCab serial no. plate
• 3.4.4. Axle serial no. plate
• 3.4.5. Transmission serial no. plate
• 3.4.6. Seat operator serial no. plate
• 3.4.7. Position of service meter
• 3.4.8. Table to enter serial no. and distributor
• 3.5. Contents
• 3.6. Dimensions, weights and operating data
• 3.6.1. WA1505H Dimensions, weights and operating data
• 3.7. CEConforming equipment
• 3.7.1. CEConforming equipment
• 3.7.2. Manufacturersupplied CEConforming equipment, according to document 41693H1120
• 4. Safety
• 4.1. Safety labels
• 4.1.1. Location of safety labels
• 4.1.2. Presentation of safety labels
• 4.2. General precautions
• 4.3. Precautions for operation
• 4.3.1. Starting engine
• 4.3.2. Operation
• 4.3.3. Transportation
• 4.3.4. Battery
• 4.3.5. Towing
• 4.4. Precautions for maintenance
• 4.5. Precautions with tires
• 5. Operation
• 5.1. General view
• 5.1.1. General view of machine
• 5.1.2. General view of controls and gauges
• 5.2. Explanation of components
• 5.2.1. Machine monitor
• 5.2.2. Switches
• 5.2.3. Control levers, pedals
• 5.2.4. Steering tilt lock lever
• 5.2.5. Cap and cover with lock
• 5.2.6. Safety bar
• 5.2.7. Towing pin
• 5.2.8. Grease pump
• 5.2.9. Cab door inner lock
• 5.2.10. Cab door open lock
• 5.2.11. Cab window open lock cancel knob
• 5.2.12. Fuse
• 5.2.13. Slow blow fuse
• 5.2.14. Power outlet
• 5.2.15. Storage box
• 5.2.16. Air conditioner
• 5.2.17. Handling cab wiper
• 5.3. Operation
• 5.3.1. Check before starting engine, adjust
• 5.3.2. Starting engine
• 5.3.3. Operations and checks after starting engine
• 5.3.4. Stopping engine
• 5.3.5. Moving the machine (directional, speed), stopping the machine
• 5.3.6. Turning
• 5.3.7. Operation of work equipment
• 5.3.8. Work possible using wheel loader
• 5.3.9. Precautions for operation
• 5.3.10. Adjusting work equipment posture
• 5.3.11. Parking machine
• 5.3.12. Check after stopping engine
• 5.3.13. Checks after completion of operation
• 5.3.14. Locking
• 5.3.15. Handling the tires
• 5.4. Transportation
• 5.4.1. Transportation procedure
• 5.4.2. Loading, unloading work with trailers
• 5.4.3. Lifting machine
• 5.5. Cold weather operation
• 5.5.1. Precautions for low temperature
• 5.5.2. Precautions after completion of work
• 5.5.3. After cold weather
• 5.5.4. Warmingup operation for steering hydraulic circuit in cold weather
• 5.6. Longterm storage
• 5.6.1. Before storage
• 5.6.2. During storage
• 5.6.3. After storage
• 5.7. Troubleshooting
• 5.7.1. When machine runs out of fuel
• 5.7.2. Towing the machine
• 5.7.3. If battery is discharged
• 5.7.4. Other trouble
• 6. Maintenance
• 6.1. Guides to maintenance
• 6.2. Outlines of service
• 6.2.1. Handling oil, fuel, coolant, grease and carrying out KOWA (KOMATSU Oil Wear Analysis)
• 6.2.2. Outline of electric system
• 6.3. Wear parts
• 6.3.1. Wear parts list
• 6.4. Fuel, coolant and lubricants
• 6.4.1. Lubrication chart
• 6.4.2. Proper selection of fuel, coolant and lubricants
• 6.5. Standard tightening torques for bolts and nuts
• 6.5.1. Torque list
• 6.6. Periodic replacement of safety critical parts
• 6.7. Maintenance schedule chart
• 6.7.1. Maintenance schedule chart
• 6.8. Service procedure
• 6.8.1. Initial 250 hours service (only after the first 250 hours)
• 6.8.2. When required
• 6.8.3. Check before starting
• 6.8.4. Every 50 hours service
• 6.8.5. Every 100 hours service
• 6.8.6. Every 250 hours service
• 6.8.7. Every 500 hours service
• 6.8.8. Every 1000 hours service
• 6.8.9. Every 2000 hours service
• 6.8.10. Every 4000 hours service
• 7. Technical Data
• 7.1. Technical data
• 7.2. Noise emission levels
• 7.3. Vibration level
• 8. Attachments, Options
• 8.1. Selecting bucket and tires
• 8.2. Method of using 2 levers
• 8.2.1. Explanation of components
• 8.2.2. Operation
• 8.3. Central lubrication system
• 8.3.1. Operating the central lubrication system
• 8.3.2. Display and control unit
• 8.3.3. Changing the lubrication interval times
• 9. Index
• 9.1. Index
• 10. Notes