Description
-
Model List:
- WA600-6R Wheel Loader
- 1. Cover
- 2. Block outline
- 3. Principal component dimension table
- 4. Work space layout
- 5. General assembly schedule
- 6. List of equipment, jigs, tools and consumables
- 7. Oil, grease and paints
- 8. Assembly procedure
- 8.1. Oil and coolant
- 8.2. Oil and coolant capacity
- 8.3. Setting the front axle and bare machine to stationary position
- 8.4. Installing the front axle
- 8.5. Connecting the drive shaft
- 8.6. Connecting the brake pipe
- 8.7. Connecting the brake pipe (Brake cooling specification)
- 8.8. Installing tire and rim assembly
- 8.9. Installing step
- 8.10. Installing cab (1)
- 8.11. Installing cab (2) (AJSS specification)
- 8.12. Installing cab (2) (Steering wheel specification)
- 8.13. Installing cab (2) (AJSS and steering wheel specification)
- 8.14. Installing cab (3)
- 8.15. Installing cab (4) (AJSS specification)
- 8.16. Installing cab (4) (Steering wheel specification)
- 8.17. Installing cab (5) (Steering wheel specification)
- 8.18. Installing cab (6) (AJSS and steering wheel specification)
- 8.19. Installing cab harness (1/2)
- 8.20. Installing cab harness (2/2)
- 8.21. Installing cab duct (1/3)
- 8.22. Installation procedure for cab duct
- 8.23. Installing cab duct (2/3)
- 8.24. Installing cab duct (3/3)
- 8.25. Installation of yellow rotary lamp
- 8.26. Installation of undercab cover
- 8.27. Installing front fender
- 8.28. Installing front light support and connection
- 8.29. Installing muffler stack and mirror
- 8.30. Installing counterweight (Standard and 1 ton heavier counterweight specifications)
- 8.31. Installing counterweight (Load and carry specification)
- 8.32. Installing pin (Standard and EU specifications)
- 8.33. Installing rear access ladder and L.H. platform
- 8.34. Installation of platform (R.H.) support
- 8.35. Installing the left handrail
- 8.36. Installing right platform and R.H. handrail
- 8.37. Installing fire extinguisher
- 8.38. Installing the rear fender mudguard plate
- 8.39. Installing rear fender
- 8.40. Installing cab undercover
- 8.41. Checking of sections
- 8.42. Air bleeding of work equipment hydraulic circuit and respective cylinders
- 8.43. Starting engine (1/2)
- 8.44. Starting engine (2/2)
- 8.45. Bleeding air from brake system
- 8.46. Installing lift arm and bell crank assembly
- 8.47. Connection of autogreasing boom piping (Autogreasing spec.)
- 8.48. Installing bucket cylinder (Bell crank side)
- 8.49. Installing bucket (1/3)
- 8.50. Installation of bucket (1) (Autogreasing spec.)
- 8.51. Installing bucket (2/3)
- 8.52. Installation of bucket (2) (Autogreasing spec.)
- 8.53. Installation of bucket (2) (Autogreasing spec.)
- 8.54. Installing bucket (3/3)
- 8.55. Greasing (1st time)
- 8.56. Greasing (1st time) Autogreasing spec.
- 8.57. Installing lift arm positioner
- 8.58. Contents of adjustment items
- 8.59. Setting of machine monitor
- 8.60. Adjustment of work equipment controller lift arm angle
- 8.61. Adjustment of work equipment EPC starting current (1/2)
- 8.62. Adjustment of work equipment EPC starting current (2/2)
- 8.63. Adjustment of bucket positioner (1/2)
- 8.64. Adjustment of bucket positioner (2/2)
- 8.65. Adjustment of load meter lift arm angle
- 8.66. Load meter noload calibration
- 8.67. Deleting the electrical system failure history (1/2)
- 8.68. Deleting the electrical system failure history (2/2)
- 8.69. Installing the floor mat (AJSS specification)
- 8.70. Installing the floor mat (Steering wheel specification)
- 8.71. Runningin procedure (1/2)
- 8.72. Runningin procedure (2/2)
- 8.73. Greasing (2nd time)
- 8.74. Greasing (2nd time) Autogreasing spec.
- 8.75. Adding grease with autogreasing pump Autogreasing spec.
- 8.76. Setting of autogreasing pump controller Autogreasing spec.
- 8.77. Touch up work
- 8.78. On use of starter kit (dummy harness) and precaution on its use
- 8.79. Starter kit (dummy harness) assembling procedure
- 8.80. Check tire pressure and inflate tire
- 9. Appendix Machine check sheet for field assembly
There are no reviews yet.