Yanmar ViO15-2 Excavator Operation And Maintenance Manual

Description

• Model List:
  • ViO15-2 Excavator

• 1. FOREWORD
• 2. Introduction
• 3. Safety Information
• 4. Product Overview
• 4.1. Intended uses
• 4.2. Break in period
• 4.3. Conditions to be met to assure compliance with EPA emission standards Conditions de conformi…
• 5. Operation License
• 6. Ordering Replacement Parts and Service Calls
• 6.1. Location of machine serial number plate
• 6.2. Location of engine serial number plate
• 6.3. Location of EPA emission control plates Localisation de la plaque signalétique EPA
• 6.4. Warranty term for the exhaust emission control system and parts Durée de garantie pour lens…
• 6.5. Ordering replacement parts and service calls
• 7. Contents
• 8. Basic Precautions
• 9. Operating Precautions
• 9.1. Precautions before starting the engine
• 9.2. Precautions for starting the engine, working and parking
• 9.3. Precautions for transportation
• 9.4. Precautions for the battery
• 9.5. Precautions for towing
• 9.6. Precautions for hooked bucket
• 10. Precautions for Servicing
• 10.1. Precautions before servicing
• 10.2. Precautions during servicing
• 11. Safety Messages (Warning Labels)
• 11.1. Location of warning labels
• 12. OPERATION
• 13. Identification of Important Parts
• 13.1. Overview of the machine
• 13.2. Controls and switches
• 14. Description of Control Devices
• 14.1. Monitors
• 14.2. Switches
• 14.3. Control levers and pedals
• 14.4. Engine hood
• 14.5. Storage compartment for the operation maintenance manual
• 14.6. Operators seat
• 14.7. Fuse
• 15. Operating Instructions
• 15.1. Checking before starting the engine
• 15.2. Starting up the engine
• 15.3. Operating and checking instructions after starting the engine
• 15.4. Traveling
• 15.5. Steering
• 15.6. Stopping the machine
• 15.7. Swinging the upperstructure
• 15.8. Operating the implement
• 15.9. Operating the track gauge change
• 15.10. Precautions for operating the implement
• 15.11. Precautions for working
• 15.12. Precautions for going up and down a slope
• 15.13. Escaping from the mud
• 15.14. Operations using the bucket
• 15.15. Replacing the bucket
• 15.16. Reversing the bucket
• 15.17. Parking the machine
• 15.18. Inspection requirements after completing operation
• 15.19. Stopping the engine
• 15.20. Inspection requirements after stopping the engine
• 15.21. Locking
• 15.22. Handling the rubber crawlers
• 15.23. Handling hydraulic P.T.O.
• 16. Transportation
• 16.1. Loading and unloading the machine
• 16.2. Precautions for loading the machine
• 16.3. Precautions for transporting the machine
• 16.4. Suspending the machine
• 17. Care and Service in Cold Weather
• 17.1. Preparing for cold weather
• 17.2. Precautions after a days work
• 17.3. After cold weather ends
• 18. Long-term Storage
• 18.1. Before storing
• 18.2. Storing
• 18.3. Using the machine again
• 19. Troubleshooting
• 19.1. Phenomena that do not constitute faults
• 19.2. Towing
• 19.3. If the battery is overdischarged
• 19.4. Troubleshooting
• 20. MAINTENANCE
• 21. Precautions for Servicing
• 22. Basic Servicing Practices
• 22.1. Oils, fuel, and cooling water
• 22.2. Electrical equipment
• 22.3. Hydraulic system
• 23. Consumables
• 24. Fueling, Oiling and Greasing Based on Temperature Range
• 24.1. Fuel and oil
• 24.2. Cooling water
• 25. Standard Tightening Torque for Bolts and Nuts
• 25.1. Required tools
• 25.2. Torque table
• 26. Replacing Essential Parts Periodically
• 27. Maintenance Table
• 27.1. Table of service time intervals
• 27.2. Service intervals when using the hydraulic breaker
• 28. Procedures for Maintenance
• 28.1. First services
• 28.2. Nonperiodic services
• 28.3. Checking before start-up
• 28.4. Maintenance every 50 service hours
• 28.5. Maintenance every 100 service hours
• 28.6. Maintenance every 200 service hours
• 28.7. Maintenance every 250 service hours
• 28.8. Maintenance every 400 service hours
• 28.9. Maintenance every 500 service hours
• 28.10. Maintenance every 1000 service hours
• 28.11. Maintenance every 2000 service hours
• 29. SPECIFICATIONS AND DIMENSIONAL DIAGRAMS
• 30. Specifications and Dimensional Diagrams
• 31. OPTIONAL PARTS AND ATTACHMENTS
• 32. General Precautions
• 32.1. Safety precautions
• 32.2. Precautions for mounting an attachment (implement)
• 33. Handling the Hooked Bucket
• 33.1. Checking the hooked bucket for damage
• 33.2. Prohibitions
• 33.3. Precautions
• 34. Optional Parts and Attachments
• 34.1. Optional parts and attachments
• 35. Maintenance Log
• 36. Notes
• 37. BACK COVER
• 38. SPINE TITLE