Komatsu D155AX-6 Bull Dozer Operation and Maintenance Manual EEAM025002

Description

• Model List:
  • D155AX-6 Bull Dozer

• 1. FOREWORD
• 1.1. BEFORE READING THIS MANUAL
• 1.2. SAFETY INFORMATION
• 1.2.1. Noise emission levels
• 1.2.2. Vibration levels
• 1.3. INTRODUCTION
• 1.3.1. USE OF MACHINE
• 1.3.2. FRONT/REAR, LEFT/RIGHT DIRECTIONS OF MACHINE
• 1.3.3. VISIBILITY FROM OPERATORS SEAT
• 1.4. NECESSARY INFORMATION
• 1.4.1. PRODUCT IDENTIFICATION NUMBER (PIN), MACHINE SERIAL NO. PLATE
• 1.4.2. EPA REGULATIONS, ENGINE NUMBER PLATE
• 1.4.3. BLADE SERIAL NO. PLATE POSITION
• 1.4.4. RIPPER SERIAL NO. PLATE POSITION
• 1.4.5. ROPS, FOPS NO. PLATE POSITION
• 1.4.6. POSITION OF SERVICE METER
• 1.4.7. TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
• 1.4.8. MACHINE SERIAL NUMBER PLATE
• 1.5. ATTACHMENTS, OPTIONS
• 1.5.1. POSITIONS OF SAFETY PICTOGRAMS
• 1.5.2. SAFETY LABELS
• 1.6. GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTENANCE
• 1.6.1. PRECAUTIONS BEFORE STARTING OPERATION
• 1.6.2. PREPARATIONS FOR SAFE OPERATION
• 1.6.3. FIRE PREVENTION
• 1.6.4. PRECAUTIONS WHEN GETTING ON OR OFF MACHINE
• 1.6.5. DO NOT GET CAUGHT IN WORK EQUIPMENT
• 1.6.6. PRECAUTIONS RELATED TO PROTECTIVE STRUCTURES
• 1.6.7. UNAUTHORIZED MODIFICATION
• 1.6.8. PRECAUTIONS RELATED TO ATTACHMENTS AND OPTIONS
• 1.6.9. PRECAUTIONS WHEN RUNNING ENGINE INSIDE BUILDING
• 1.7. PRECAUTIONS FOR OPERATION
• 1.7.1. PRECAUTIONS FOR JOBSITE
• 1.7.2. STARTING ENGINE
• 1.7.3. OPERATION
• 1.7.4. TRANSPORTATION
• 1.7.5. TOWING
• 1.8. PRECAUTIONS FOR MAINTENANCE
• 1.8.1. PRECAUTIONS BEFORE STARTING INSPECTION AND MAINTENANCE
• 1.8.2. PRECAUTIONS FOR INSPECTION AND MAINTENANCE
• 2. OPERATION
• 2.1. GENERAL VIEW
• 2.1.1. GENERAL VIEW OF MACHINE
• 2.1.2. GENERAL VIEW OF CONTROLS AND GAUGES
• 2.2. EXPLANATION OF COMPONENTS
• 2.2.1. MACHINE MONITOR
• 2.2.2. SWITCHES
• 2.2.3. CONTROL LEVERS, PEDALS
• 2.2.4. DUST INDICATOR
• 2.2.5. BATTERY DISCONNECT SWITCH (if installed)
• 2.2.6. FUSE BOX
• 2.2.7. DOOR POCKET
• 2.2.8. ASHTRAY
• 2.2.9. CAR RADIO, HANDLING
• 2.2.10. CAR STEREO, HANDLING
• 2.2.11. HANDLING AIR CONDITIONER
• 2.3. OPERATION
• 2.3.1. CHECK BEFORE STARTING ENGINE, ADJUST
• 2.3.2. STARTING ENGINE
• 2.3.3. OPERATIONS AND CHECKS AFTER STARTING ENGINE
• 2.3.4. STOPPING ENGINE
• 2.3.5. MOVING MACHINE
• 2.3.6. STOPPING MACHINE
• 2.3.7. SHIFTING GEAR
• 2.3.8. SHIFTING BETWEEN FORWARD AND REVERSE
• 2.3.9. STEERING MACHINE
• 2.3.10. PRECAUTIONS FOR OPERATION
• 2.3.11. PARKING MACHINE
• 2.3.12. CHECK AFTER STOPPING ENGINE
• 2.3.13. CHECK AFTER FINISHING WORK
• 2.3.14. LOCKING
• 2.3.15. RIPPER OPERATION
• 2.3.16. OPERATING METHOD FOR RIPPING OPERATIONS
• 2.3.17. WORK POSSIBLE USING BULLDOZER
• 2.3.18. ADJUSTING POSTURE OF WORK EQUIPMENT
• 2.3.19. TIPS FOR LONGER UNDERCARRIAGE LIFE
• 2.4. TRANSPORTATION
• 2.4.1. LOADING, UNLOADING WORK
• 2.4.2. METHOD OF LIFTING MACHINE
• 2.4.3. PRECAUTIONS FOR TRANSPORTATION
• 2.4.4. TRAVELING ON ROADS
• 2.4.5. REMOVAL OF CAB
• 2.5. COLD WEATHER OPERATION
• 2.5.1. PRECAUTIONS FOR LOW TEMPERATURE
• 2.5.2. AFTER COMPLETION OF WORK
• 2.5.3. AFTER COLD WEATHER
• 2.6. LONGTERM STORAGE
• 2.6.1. BEFORE STORAGE
• 2.6.2. DURING STORAGE
• 2.6.3. AFTER STORAGE
• 2.6.4. STARTING MACHINE AFTER LONGTERM STORAGE
• 2.7. TROUBLESHOOTING
• 2.7.1. AFTER RUNNING OUT OF FUEL
• 2.7.2. METHOD OF TOWING MACHINE
• 2.7.3. IF BATTERY IS DISCHARGED
• 2.7.4. OTHER TROUBLE
• 3. MAINTENANCE
• 3.1. GUIDES TO MAINTENANCE
• 3.2. OUTLINES OF SERVICE
• 3.2.1. HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC
• 3.2.2. OUTLINE OF ELECTRIC SYSTEM
• 3.3. WEAR PARTS
• 3.3.1. WEAR PARTS LIST
• 3.4. RECOMMENDED FUEL, COOLANT, AND LUBRICANT
• 3.4.1. RECOMMENDED BRANDS, RECOMMENDED QUALITY FOR PRODUCTS OTHER THAN KOMATSU GENUINE OIL
• 3.5. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
• 3.5.1. TORQUE LIST
• 3.6. PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
• 3.6.1. SAFETY CRITICAL PARTS
• 3.7. MAINTENANCE SCHEDULE CHART
• 3.7.1. MAINTENANCE SCHEDULE CHART
• 3.8. SERVICE PROCEDURE
• 3.8.1. INITIAL 250 HOURS SERVICE (ONLY AFTER THE FIRST 250 HOURS)
• 3.8.2. WHEN REQUIRED
• 3.8.3. CHECK BEFORE STARTING
• 3.8.4. EVERY 250 HOURS SERVICE
• 3.8.5. EVERY 500 HOURS SERVICE
• 3.8.6. EVERY 1000 HOURS SERVICE
• 3.8.7. EVERY 2000 HOURS SERVICE
• 3.8.8. EVERY 4000 HOURS SERVICE
• 3.8.9. EVERY 8000 HOURS SERVICE
• 4. SPECIFICATIONS
• 4.1. SPECIFICATIONS
• 5. ATTACHMENTS, OPTIONS
• 5.1. GENERAL PRECAUTIONS
• 5.1.1. PRECAUTIONS RELATED TO SAFETY
• 5.2. INTRODUCTION OF ATTACHMENTS AND OPTIONS
• 5.2.1. INTRODUCTION OF ATTACHMENTS AND OPTIONS
• 5.3. HEADREST, HANDLING
• 5.4. CAP WITH LOCK, HANDLING
• 5.4.1. METHOD OF OPENING AND CLOSING CAP WITH LOCK
• 5.5. PROCEDURE FOR SELECTING RIPPER POINT
• 5.5.1. PROCEDURE FOR SELECTING RIPPER POINT
• 5.6. HANDLING MACHINES EQUIPPED WITH KOMTRAX
• 5.6.1. BASIC PRECAUTIONS